PDA

View Full Version : R1 (1999) rear wheel in a curvey?


LiamH
15-01-10, 10:02 AM
Has anyone done this? I've had a search and there's some hints that it might have been done, but no detail.

I've got a spare R1 back wheel and a shed full of part worn 180's in can use, ya see!

BoltonSte
15-01-10, 10:07 AM
I did it but by using a JMC top braced swing arm (which I have for sale ;)) which was made to bolt on the SV and take the wheel/caliper.

Ste

Alpinestarhero
15-01-10, 10:09 AM
Hmm...you'll need to measure things like spacers, and clearance between the swingarm and tyre. Bandit 1200 wheels have been used by some other people with differant spacers

Why not get the wheel on there and see how it measures up? You might have some problem with the axle, I imagine an R1 would have a beefier (see: thicker) axle which may not go through the SV swingarm?

LiamH
15-01-10, 10:29 AM
I'm expecting to have to make up new spacers as the R1 spindle is twice the size of the SV twig...the difference will allow for some captive spacers to fit in.

Like you say, I'll chuck it in and see how it measures up.

Hmm...you'll need to measure things like spacers, and clearance between the swingarm and tyre. Bandit 1200 wheels have been used by some other people with differant spacers

Why not get the wheel on there and see how it measures up? You might have some problem with the axle, I imagine an R1 would have a beefier (see: thicker) axle which may not go through the SV swingarm?

yorkie_chris
15-01-10, 12:40 PM
Measure from RHS of swingarm to center of wheel and to disc etc.

There is rear wheel thread here
http://forum.svrider.com/showthread.php?t=78545&page=130
if you can be bothered to read through all svxr's bullsht about how a gsxr wheel is a million tonnes lighter if you inflate it with unobtanium dioxide there's some pretty good info there.

Remember swingarm bends in a few mm. Measure all clearances before you remove OEM wheel.

smoky
15-01-10, 12:52 PM
why you want to do that? the wheel will most likely be heavier (unless it's a CF?), so you will loose acceleration... R1 runs 190's in the back, the bike will corner like crap with 190 tire in the back... even with 180 you will notice it is slow turning. R1 also uses heavier chain (530), there are 520's for r1, but i have not seen 525.... never looked though, so not too sure .
just my opinion. :)

yorkie_chris
15-01-10, 01:03 PM
The wheel will probably be slightly lighter but not enough to offset the larger tyre.

Why you think it will corner crap with a 190 on the back? taller profile will raise back and steepen head angle.

You will probably need to use a 520 chain for clearance anyway, people putting GSXR wheel on use 520 front sprocket and flip it over so it is offset outwards.

smoky
15-01-10, 01:19 PM
i have tried larger size tires on cbr6, gsxr600 and KTM suprduke... they look good, but the result was always 'sluggish' turning... i still have nearly new 190 that i pulled of my SD half way through last track day, it handled so bad. i believe it has something to do with the size of the contact patch, but i'm no expert... Having said that, i do not have much experience with the SV (it's my wife's bike) and never actually tried it on SV...

zadar
15-01-10, 07:47 PM
You will probably need to use a 520 chain for clearance anyway, people putting GSXR wheel on use 520 front sprocket and flip it over so it is offset outwards.
That is front sprocket to bring it in line with rear. Either 520 or 525 chain will be same distance from tire since back side of sprocket is flat.

maviczap
15-01-10, 07:53 PM
I did it but by using a JMC top braced swing arm (which I have for sale ;)) which was made to bolt on the SV and take the wheel/caliper.

Ste

Where is it for sale? On the Bay

davepreston
15-01-10, 08:28 PM
pm ste and he'll sell you it , it in his garge collecting dust at present

maviczap
15-01-10, 08:40 PM
PM sent. Thanks DP

speedplay
15-01-10, 08:43 PM
Where is it for sale? On the Bay


not another mod that will wait in the garage for you to find the time to do ;)

maviczap
15-01-10, 08:48 PM
not another mod that will wait in the garage for you to find the time to do ;)

Would take a couple of hours to do ;) Especially as I've laid some lovely shag pile in the garage today to keep my tootsies at bit warmer. Got a heater off Evilbay as well, so progress will begin in ernest- once I get back from working away all next week :rolleyes:

Work work work ... no rest for the wicked :p

I'm begining to wonder if you're stalking every post I make SP ;)

BoltonSte
15-01-10, 09:03 PM
pm ste and he'll sell you it , it in his garge collecting dust at present

No it's not, it is in my celler as part of my collection of modern vehicular art.

OK it's downstairs with the rest of the parts as I couldn't get the bike into the garage...and Dave, you've seen the size of my garage!

Maviczap:

PM replied to.

Ste

speedplay
16-01-10, 01:36 PM
I'm begining to wonder if you're stalking every post I make SP ;)


Nah, I'm just bored and you seem to post all over the place!!

I know what its like to have a stalker though..I seem to have picked one up myself, Deep joy:rolleyes: