View Full Version : Breaking curvy naked K1 - lots of trick bits
yorkie_chris
23-01-16, 04:57 PM
Engine - done a lot of miles, bit rattly but starts and runs fine and makes decent power. K1 version so no bother with oil starvation like earlier or throwing rods like later. Bought it at 18k and it's now on 100k. Oil changed every 3k, valve clearances every 12k usually.
£100
JHS stage 2 cams. Suit pointy or curvy, £150
M4 full race system to suit curvy. Would fit pointy but need mod to oil cooler £150
Penske 8987 triple clicker shock sprung for 12-13st rider. Fresh oil and service less than 1k ago though it's done over 40k in total it was like new inside... as you'd expect for a grands worth of shock. £300 sold
GSXR 600 SRAD/K1 hybrid front end. Right way up forks, 4 pot calipers, srad discs, K1 cartridges with very special midvalve-based compression damping. Braking response is awesome on them but they're slightly harsh on initial bump response, nothing you can't live with. £500 for the entire front end. Only issue is a dent on the front rim which motoliner could undent. £300
GSXR K1 clocks with connector and loom bits and speedo healer to make them work with the SV. £80. Also have small circuit to make rev counter work and parts to make a thing to make the fuel light work.
Ducati 999 caliper and fitting kit £80 or swingarm with good bearings including fitting kit and caliper and the lot inc braided hose £100
Stebel nautilus air horn, split compressor and horn connected with hose £20
GB moto rearsets bit rough some spares included £50
There's a load of other bits of random crap, the rest of the bike for one thing. Some rough as **** black plastics that have been down the road, repeatedly, a couple of fuel tanks, a set of (slightly rattly but fine to use) EBC prolite ductile iron SRAD discs. SRAD 750 yokes. Some ported SV heads. A wiseco 700cc kit. Some busa pistons. Lightened spragclutch/flywheel assembly. Total loss/lightened flywheel.
CB500Racer
23-01-16, 05:51 PM
How much for the ported heads, whats the condition of them are they curvy heads or injection.
Do you also have the setup info to go with the jhs cams too.
also what condition is the M4 system like, has it been down the road at all.
thanks
john
yorkie_chris
23-01-16, 07:17 PM
There's a small dent on the M4 link pipe, it would probably knock out.
The ported heads I'm not sure, they have just been matched to the manifold and 600 grit polished, slight smoothing on throat but very little, exhausts are matched and mirror polished. £150? They're clean spot on ready to fit. I was going to mill them down a few thou but thought you could get same effect by thinner gasket so didn't bother. (however my mate has first dibs on these just now).
Setup info for JHS cams... none needed, they have as-stock timing marks so easy to fit.
johnnyrod
23-01-16, 09:08 PM
Chris you had a rear hugger for a curvy, is that offer still there?
CB500Racer
24-01-16, 02:37 PM
Thanks for the info, if your mate doesn't want them give me a PM
John
yorkie_chris
24-01-16, 04:32 PM
Chris you had a rear hugger for a curvy, is that offer still there?
yes if i can find it
Hi Chris you still got the M4? any chance of a couple of pics? 1 of link pipe damage 1 of can and 1 of full system fitted please whatsapp to:
07882157252 are you in Halifax?
Thanks
Neil
TOLAROS
24-01-16, 09:06 PM
Pics of the clocks?Do you have carbs?
yorkie_chris
25-01-16, 11:58 AM
Yes have some carbs that are alright... been rejetted to suit bmc race rs filter (also for sale)
Redmist
25-01-16, 01:07 PM
Dibs on shock - PM'd
Redmist
25-01-16, 10:29 PM
Shock un-dibbed :)
yorkie_chris
25-01-16, 10:41 PM
Hi Chris you still got the M4? any chance of a couple of pics? 1 of link pipe damage 1 of can and 1 of full system fitted please whatsapp to:
07882157252 are you in Halifax?
Thanks
Neil
I don't do whatsapp or that carry on, I'll MMS them to you tomorrow night
Keighley now
yorkie_chris
25-01-16, 10:42 PM
There's the rest of the bike to go at as well.
Decent rear wheel with a PR3. Avon storm front. etc.
Redmist
26-01-16, 02:08 PM
P.S. I only undibbed the shock because I'm an idiot, not because I think there is anything wrong with it!
Good luck with the sales!!
I don't do whatsapp or that carry on, I'll MMS them to you tomorrow night
Keighley now
Thanks
yorkie_chris
27-01-16, 11:14 AM
Sent you a message with some pics. If you're bothered I have a zip wheel and scotch wheels for the grinder I can give it a tidy up with once it's off the bike.
Any chance of the side stand? Unless of course the bike is still largely in one piece and you need it to keep it upright!
yorkie_chris
30-01-16, 11:26 PM
Yeah it's still in one piece just now, you're welcome to it when I've split it up though. I think it's a GSXR1000 one but sod it it's a stand...
That's great thanks, keep me posted
antonashcroft
08-02-16, 09:19 PM
did it have fairing lowers?
maviczap
09-02-16, 07:27 AM
did it have fairing lowers?
Its a naked no fairings :)
yorkie_chris
10-02-16, 08:47 AM
Were you after a hugger mavis?
maviczap
10-02-16, 09:01 AM
No mate, would love your trick bits, but no funds :-(
doghammer
10-02-16, 10:12 AM
Is the M4 full system still available? if so do you have photos of the dent?
Thanks!
yorkie_chris
10-02-16, 12:20 PM
Yes and yes, PM me an email address
yorkie_chris
10-02-16, 10:56 PM
Corbin comfort seat
Renntec luggage rack (much abused but been TIG welded back together!)
Both available
dirtydog
13-02-16, 08:01 AM
How much for the Corbin Chris?
yorkie_chris
13-02-16, 09:55 AM
£60?
yorkie_chris
04-04-16, 07:08 AM
Bump
Price reduction on bits, see OP
CB500Racer
04-04-16, 09:23 PM
Chris do you still have the M4 system for sale. whats the silencer like on it.
yorkie_chris
06-04-16, 10:24 AM
Yes still here http://i160.photobucket.com/albums/t184/yorkie_chris/20160305_152612.jpg
yorkie_chris
06-04-16, 10:25 AM
had a couple of knocks but it's functional and been packed recently. Could do with a clean and a bit of banding on the front end
Cams still available?
Are these equivalent of the pointy to curvy swap?
yorkie_chris
08-04-16, 10:35 AM
Yes
Apparently different durations to pointy curvy cam swap as they were designed as performance cams from the start
And life is easier because they have normal markings on them
Replied to pm. Apologies for the delay I was a bit busy with this;
http://uploads.tapatalk-cdn.com/20160415/0a9503492cd9f62b0b9042e77f160a08.jpg
http://uploads.tapatalk-cdn.com/20160415/cdb169292d8b4b6295f1de87f43547b9.jpg
maviczap
15-04-16, 06:30 PM
That's the worst excuse ever! ;)
Many congratulations!
Congrats Claude! Here's to many many sleepless nights bud!
andrewsmith
15-04-16, 09:29 PM
Congratulations
Sent from my E2303 using Tapatalk
dirtydog
21-04-16, 10:41 PM
You got a pic of the renntec rack Chris?
yorkie_chris
22-04-16, 08:49 PM
Sorry mate it's gone
Yes still here http://i160.photobucket.com/albums/t184/yorkie_chris/20160305_152612.jpg
is this low level or has it been modded?
is the link pipe removable on this system?
what is the linkpipe diameter?
yorkie_chris
24-04-16, 07:15 AM
Low level, I had it on daytona 955 pillion pegs so it kicked up at the back but it's normal height.
Link pipe removable.
yorkie_chris
24-04-16, 07:18 AM
54.5 approx OD where it slips into the end can
Sorry Chris. No need for the cams now. SV is being sold.
yorkie_chris
05-05-16, 07:43 PM
Bugger, serve me right for messing around!!
Cams still here all boxed up and ready to go :)
Bugger, serve me right for messing around!!
Cams still here all boxed up and ready to go :)
Sorry dude :(
Lordlucan
10-05-16, 04:18 PM
Hi Yorke, I've bought Claude's bike and am considering doing the cam swap. Are they still available and if so, are you open to offers?
Sent from my Nexus 6P using Tapatalk
yorkie_chris
10-05-16, 04:42 PM
Yup
Lordlucan
10-05-16, 04:48 PM
Pm sent
Sent from my Nexus 6P using Tapatalk
mike636
12-05-16, 01:08 PM
would you do the m4 and rearsets for 150?
Lordlucan
12-05-16, 01:19 PM
Send me payment details for the cams too [emoji6] [emoji38] before I do a Claude on you and sell up
Sent from my Nexus 6P using Tapatalk
vBulletin® , Copyright ©2000-2025, Jelsoft Enterprises Ltd.