Stowable jack
 

I wish I could say this was my idea, alas, it is not. I saw something similar to this at a motorcycle show this spring. The concept was intriguing and the cost was unreasonable. I came home and cranked a similar one out in about 45 minutes. It wasn't perfect and had some potential nasty pinch points. The original Youtube video is here.

Version II, still unpainted, but fully adjustable with a lever for some mechanical advantage and to keep soft parts away from the pinch point. The velcro strap is to lock the front brake lever so the bike won't roll and functions as a storage aid.
https://lh5.googleusercontent.com/-I...o/IMG_2433.JPG

https://lh3.googleusercontent.com/-z...o/IMG_2434.JPG

A nut is welded onto the end of the square tube with lots of filler and then profiled with a hand grinder.
https://lh5.googleusercontent.com/-O...o/IMG_2435.JPG

So in about 30 seconds, you can lock the brake...
https://lh3.googleusercontent.com/-Z...o/IMG_2438.JPG

...and raise the rear wheel off the ground.
https://lh4.googleusercontent.com/-r...o/IMG_2437.JPG

It fits easily in the rear compartment.
https://lh4.googleusercontent.com/-n...o/IMG_2439.JPG

Re: Stowable jack
 

Nice work. Are you going to be making any to sell?

Re: Stowable jack
 

No, this is just for my use. I found the item that I shamelessly copied. I think I have made some minor improvements. The lever on my version works very well. Here's a link to a review of the original unit.
http://www.webbikeworld.com/motorcyc...e-jack-review/

Re: Stowable jack
 

Yours connects to the bike better and has a way more stable looking foot. Nice work.

Re: Stowable jack
 

Terry. would you mind me using your 'minor improvements' to make these up. i'm in the position to knock these out if people are wanting them.

i seen these ages ago and thought there's a good idea but never got round to it as i never seen a market here on the org.

Re: Stowable jack
 

I have no issue at all. If you have any questions, ask away. I have not yet purchased/built a true track stand or the matching pins that thread into the swing arm. As depicted, I just used a SS bolt and a matching divot in the jack. I't secure and won't slip out.

Re: Stowable jack
 

i'm in two minds as to which way to go, either a swinging L bracket or the bolt method. the L bracket would mean that you could use it for other people bikes as well just in case.

Re: Stowable jack
 

Or make it both ways with an L bracket insert.

Re: Stowable jack
 

that means extra fabrication.. lol.

i just had a thought. instead of the hight adjuster at the bottom being a screw thread i could make the top hight adjustable via holes like axle stands and use the lever as the pin. with the lever i would put a stop on the main shaft and an R clip through a hole at the back.

Re: Stowable jack
 

Just keep in mind that the closer your lever is to the pivot, the less oomph required. Something about first class levers???

Re: Stowable jack
 

it dont take that much effort to lift a bike over on its side stand. but you do have a valid point.

Re: Stowable jack
 

ok i have had another think about the interface. a bolt with a bar on the end to create a T bar/bolt and also a cut outs on the top of the stand for the T bar and paddock stand bobbins. if there are no bobbins then you would wind the T Bar on and use that.

Re: Stowable jack
 

Go for it Bibs! I would have one if you made them, it's this or a scottoiler and I cant be bothered putting a scottoiler on when I am only a weekend warrior at the moment...

Re: Stowable jack
 

Do it

Sent from my D2303 using Tapatalk

Re: Stowable jack
 

Another interested party, looks good to add to the traveling tool/puncture repair kit if made.

Re: Stowable jack
 

I would be interested :)

Re: Stowable jack
 

Make a matched pair and you've got a full portable paddock stand. If you want a design challenge ;)

Re: Stowable jack
 

I'm on board. :)

Re: Stowable jack
 

I'll take one as too. Oh, wait... I already have one:takeabow:
There's no wiseguy/smartazz smilie:(

Re: Stowable jack
 

i gave this some thought again. think i'll use both ideas but basically a snap jack but with design modifications.

the pin on the snap jack will also be a lever and i'll put a foot on like Terry has. the mounting will be cut for using the T bolt, plain bolt (if you loose the t bolt) and bobbin.

it'll be a while but next time i'm messing around at the workshop i'll get a proto punched and folded.

Re: Stowable jack
 

never got the chance yesterday to have a go at these so i will wait till the next rainy sunday.