My sv front end swap (RSV mille) and rebuild (loads of pics)
 

well after my off i managed to get hold of a rsv mille front end so hear is my log of what i have done so far :)

well this was the bike stripped down after my off all the damaged parts removed to be replaced/repaired

http://i357.photobucket.com/albums/o...2/P1040538.jpg

then i sorted this lot out while waiting for the forks and stuf, and sent off the sv stem to be pressed in to the rsv yoke

all panels repaired and fitted
http://i357.photobucket.com/albums/o...2/P1040545.jpg

My make shift head bearing tool, lol old race cut so i can hammer the new tapered race in, the cutting of the old race took ages must be hardened steal
http://i357.photobucket.com/albums/o...2/P1040541.jpg

new race pressed in
http://i357.photobucket.com/albums/o...2/P1040540.jpg

new taperd bearings in, need to get some grease though
http://i357.photobucket.com/albums/o...2/P1040542.jpg

tided the mess of cables up at the front, moved to behind the head stock, had to cut the air box snorkel to make sure it could breath enough with the cables there
http://i357.photobucket.com/albums/o...2/P1040550.jpg
http://i357.photobucket.com/albums/o...2/P1040553.jpg

New (to me) can, stubbied ART
http://i357.photobucket.com/albums/o...2/P1040549.jpg

got the brembo callipers for the new front end, they were in a right state

http://i357.photobucket.com/albums/o...2/P1040559.jpg

cleaned
http://i357.photobucket.com/albums/o...2/P1040570.jpg

and mounted up on the forks (also cleaned and polished up)
http://i357.photobucket.com/albums/o...2/P1040575.jpg

http://i357.photobucket.com/albums/o...2/P1040574.jpg

Rotors, these are pretty hefty and very thick compared to the sv ones (need a clean)
http://i357.photobucket.com/albums/o...2/P1040577.jpg


Thanks for looking

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

Keep an eye on the fuelling now you've cut the air box with the new can.
I know I have a curvy but the whole thing was dyno'd and rejetted to suit the air filter butchery and Art stubby set up(yours is much shorter than mine!).
I know things are slightly different on the pointy, but equates to the same.
TBH I reckon if it hadn't had the air filter fiddled with it would have worked perfectly fine under stock conditions...now I can't put in a standard filter as it gets really bogged down. Permanent butchered filter is the only thing she likes!

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

Did you have to re-use the old piston seals in the calipers, Barwell? I've got a sticking piston on one of mine and, according to the ducati site, there are no seal kits available. Except maybe from a KTM dealer :confused:

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

What year and model are calipers off?
If you've got an inkling that KTM is use the calipers (very good chance as the LC4 Prestige's use a brembo that looks v similar) you are probably right.

The importer for KTM is based in Peterborugh I think or try these who are the best on the web http://www.ktmforum.co.uk/showthread...r-spares/page5

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

Good job on those calipers! They look a million times better!

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

same ones as from my VRaptor on first glance, so thats anywhere from 2000-2005 off top of my head.
I know the rear brakes are same as Aprillia too. Share the same master cylinder, so pretty much reckon the front to be the same.

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

Because main jet size has been increased to suit... pointies seem to get away with snorkel mods without having many problems.

More airflow = good anyway... snorkel is only there to keep EU muppets happy.

Edited :)

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

:smt082
can't agree more on that one. Whats the betting that will be my next failure:smt093

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

I bet it will not be if you service it before it goes wrong.

Re: My sv front end swap (RSV mille) and rebuild (loads of pics)
 

Hi Pete mine were fine, but you can get the seals any way from KTM

4 pad caliper seals part NO: 61013019100 you need to buy X2 of them to do both sides, pistons per calliper par NO: 61013019000 need x2

2 pad calliper Seals Part NO: 58713021000 you need to buy x2 of them to do both sides, Pistons per calliper Part NO: 58713019000 need x2

get them from hear LINK

KTM do use the same seals (and brakes) and are the only sellers of brembo spares see above for product numbers

yup same as v raptor, also the same as some duc's and benelli's and obviously ktm's