SV650.org - SV650 & Gladius 650 Forum



Showing results 1 to 14 of 14
Search took 0.00 seconds.
Search: Posts Made By: GraemeC123
Forum: SV Talk, Tuning & Tweaking 05-10-18, 09:19 AM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Every plug I could get to I took apart and cleaned with aircraft spec electrical cleaner and coated with electrical grease.hopefully that will stop future issues.
Forum: SV Talk, Tuning & Tweaking 04-10-18, 03:22 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

So did a bit more digging today. Decided to chase some looms and found a burnt out pin on the ignition loom in the green connector. Found a spliced new wire wiggled it and it seems to be working fine...
Forum: SV Talk, Tuning & Tweaking 29-09-18, 09:34 AM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Yeah checked the plugs and they all looked good, colour was spot on and gaps were in spec. I was going to replace them but they are only about 1500 miles/ 10 months old as I replaced them at the...
Forum: SV Talk, Tuning & Tweaking 20-09-18, 06:17 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Yeah I already looked at that and cleaned the connector thanks for the PT no.
Forum: SV Talk, Tuning & Tweaking 20-09-18, 06:02 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

No it won't start with clutch out
Forum: SV Talk, Tuning & Tweaking 20-09-18, 06:01 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

So it would be a fair shout to replace the sidestand switch seeing as though it doesn't operate as above? Where can I get a new one online? I had a quick Google and all that seems to be coming up is...
Forum: SV Talk, Tuning & Tweaking 20-09-18, 04:56 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Seen quite a few sidestand switch intermittent faults on here so thought I would have another look. Bike will start in gear with the clutch in sidestand up as expected, when I place the sidestand...
Forum: SV Talk, Tuning & Tweaking 11-09-18, 03:57 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Forum: SV Talk, Tuning & Tweaking 11-09-18, 03:02 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Thanks to everyone for the replies I will have a look at how to do the dealer mode and report back.
Forum: SV Talk, Tuning & Tweaking 11-09-18, 02:29 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

Throttle cable free play seems fine, the first time it happened I had just rolled off the second time it had been off for a little while.
Forum: SV Talk, Tuning & Tweaking 11-09-18, 02:25 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

That's how I tested it. I wiggled the lever as I was doing it, must have operated it 50 times. Cleaned the contacts up and reconnected. Checked all the other plugs and tip over and that's all fine....
Forum: SV Talk, Tuning & Tweaking 11-09-18, 06:42 AM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

No and I checked the switch works as it should.
Forum: SV Talk, Tuning & Tweaking 10-09-18, 07:20 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Re: Cutting out as pulling up to junctions

It was dry today, my bike has the front fender extender and I always blow out as much water as possible with a airline after washing. Worth a check though so will check tomorrow. The fact it's...
Forum: SV Talk, Tuning & Tweaking 10-09-18, 06:06 PM
Replies: 47
Views: 4,843
Posted By GraemeC123
Cutting out as pulling up to junctions

Looking for some pearls from the guru's.

So I have had my sv650s 2010 faired since last December and bought from a guy off here. Done maybe 2000 miles on it without any trouble. (1000 3 weeks ago...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT. The time now is 11:51 AM.


Powered by vBulletin® - Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.