SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
ive been thinking of chainging my exhaust for something differnt, but all the ones ive seen requier the standerd system to be cut, and i dont really fancy doing that. is there one out there that fits with no cutting or am i going to have to get the old haksaw out.
oppinions/addvice greatly received |
![]() |
![]() |
#2 |
Just Ballast
Mega Poster
Join Date: Feb 2006
Location: Rugby, South Mids Group
Posts: 4,381
|
![]()
If you buy a full system made for the SV, then you won't need to cut anything.................but they are pretty expensive unless you can score one off e bay.
Otherwise..................it's hacksaw heaven ![]()
__________________
If It's Too Loud, You're Too Old! I'd Rather Have Two Big Bangs Than Four Little Strokes |
![]() |
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
![]()
so ive got to cut it then ....... oh well wich can should i go for. any ideas people
|
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
![]()
ive got a remus revolution gp oval mate its awsome, go to my you tube bit and have a look as i did 3 little vids before during and after fitting.
http://www.youtube.com/watch?v=-7uKqXVQxxQ i'll only stick the first one on here but look at the other 2 while your there mate |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]()
As Lissa said, to get away with no hacksawing you will need to fit a full system. There is an option of a half system made by Lazer, this reuses the front down pipe and requires no cutting but at a similar cost to some full systems!
Last edited by Dangerous Dave; 04-05-08 at 10:46 AM. |
![]() |
![]() |
#6 | |
Guest
Posts: n/a
|
![]() Quote:
|
|
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]()
Get cuttin it's a breeze. Much easier if you remove the stock one 2 mins. Full stock exhausts are cheap enough on the bay if you decided to go back but once you have a can on I doubt you will. Sounds much better than a hover.
|
![]() |
![]() |
#8 |
Guest
Posts: n/a
|
![]()
One piece of advice.......DON'T BUY BLUE FLAME!
Ill fitting, very badly made and expensive too. I have had nothing but trouble with mine. On the up side, customer service very good, although you would hope so with such a bad product. Also sounds VERY good with 2 removeable baffles. Once this has rattled itself to bits (in the not too distant future) I will get a fuel methinks |
![]() |
![]() |
#9 | |
Guest
Posts: n/a
|
![]() Quote:
![]() Never had a problem with mine...so far,so can(get it can) ![]() ![]() |
|
![]() |
![]() |
#10 |
Guest
Posts: n/a
|
![]()
i got the CCC stainless oval, dead easy to fit & sounds great.
not sure anout the hacksaw though - i had to use a disc saw to get though the original link pipe. |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
After market exhaust (Curvey) | SUPERSTARDJ01 | Stuff Wanted | 4 | 11-05-09 05:46 PM |
After market exhaust back box..... | SUPERSTARDJ01 | Stuff Wanted | 2 | 08-05-09 09:50 AM |
Wanted k6 after market exhaust !!!!!! | tj ready | Stuff Wanted | 6 | 14-02-09 12:47 AM |
After market Exhaust popping...bad? | Kinvig | SV Talk, Tuning & Tweaking | 8 | 21-08-07 07:10 AM |
After market exhaust | riktherider | Stuff Wanted | 0 | 01-06-07 10:48 AM |