SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
Hi all I'm having trouble with my wifes Sv, I removed the alarm solder'd the wires back together and now it wont start. when you turn on the ignition all the lights etc come on but you don't hear the fuel pump kick in, it winds over but wont start
![]() |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
![]()
sorry mate cant help but noticed your location, where about are you then?
|
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
![]()
hi. this mite soound silly but any suggestion is worth the while. have you tried checking that the bike is in neutal and the stand is down and engine run switch is to run. ino it sounds simple but you never knw.
|
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
![]()
Thanks for the reply's I have checked the kill switch and neutral don't think the stand has to be down. I'm not to far from you ad 9 miles other side of Turriff from you.
|
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]()
good to know, come and have a chat in the ecosse section sometime! hope you get the bike sorted clutch switch faulty?
|
![]() |
![]() |
#6 |
Member
Mega Poster
Join Date: Jan 2008
Location: North West
Posts: 3,124
|
![]()
I've been through this headache myself. You likely have a mistake in the wiring, sometimes part of the original wiring is removed to accomodate an alarm.
I found the easiest way was to buy a loom for comparison and spend a good session with the wiring diagram and a multimeter until you find the offending error. Check that you havent blown a fuse with all those bare wires dangling around. |
![]() |
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]()
... had the exact same problem on a K5... trust me dude lol, if its the same problem just charge the battery.. well known on all suzys to kill off the batterys.
gives a little chikachikachika.. then nothing..but the pumps priming again.. try charging the battery sounds simple.. but thats where my money is, because it may be able to hold enough to turn it on and prime the pumps but not enough to engage the starter motor. ![]() Last edited by John 675; 18-01-09 at 11:55 PM. |
![]() |
![]() |
#8 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
![]()
Read the OP
![]() Fuel pump connector is down the LHS of the bike, check this for starters. Also check the tip-over sensor. Are you sure you have connected the correct 2 wires for dealer mode? There should be a fault code displayed and "chec" should disappear.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
![]() |
![]() |
![]() |
#9 | |
Member
Mega Poster
Join Date: Jan 2008
Location: North West
Posts: 3,124
|
![]() Quote:
On mine, I found there was a connector/junction box part that had been completely removed to fit the alarm. Once I'ld figured that out I wired it up just fine but it only became obvious once I had seen another loom to compare against. |
|
![]() |
![]() |
![]() |
#10 |
Guest
Posts: n/a
|
![]()
i just think thats it the most simple explination, when the bike wont start. it would certainly pee me off if ive ripped the loom to bits then to find it was a flat battery lol,
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
A sad start to the day | ooger | Idle Banter | 17 | 03-06-08 11:27 AM |
Wont start, but will bump start :( | Wally | SV Talk, Tuning & Tweaking | 6 | 10-08-07 02:02 PM |
She won't start! Help! | Bear | SV Talk, Tuning & Tweaking | 43 | 19-12-06 11:39 AM |
yet another won't start, 01 650 | mann650 | SV Talk, Tuning & Tweaking | 4 | 25-07-06 03:54 PM |
Clocks start spinning and bike wont start?! | lockery | SV Talk, Tuning & Tweaking | 4 | 13-04-06 07:32 AM |