SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
hello all how is it going, i want to take me sv650 to a garage to get me carbs cleaned and rebalanced as it seems to be running rough also need tappets doing how much do you think this will cost if any one lives near fareham or in portsmouth could you point me into the right direction to get this done
thanks folks |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
![]()
i had an i/l 4 carbs balanced cost £30.00 as for strip and clean if i was having em balanced would do it me self couple of days before.
|
![]() |
![]() |
#3 |
Member
Mega Poster
Join Date: Jul 2008
Location: Sheffield
Posts: 10,274
|
![]()
On the assumption of an hourly rate I'd say you're looking at 1-2 hours for a carb strip & clean plus the balancing fee/time it takes to do that (under an hour?).
I think you ideally want carbs balancing after a service (or if it's been serviced very recently) if that's not the case I'd get them to clean/swap your airfilter while they're in the general area (or get it serviced too). Edit: btw I'd strongly suggest you either ask them to diagnose the fault before work or make sure you're 100% you need the work you've specified doing. Because if that doesn't solve the problem it's unnecessary cost and you're then going to have to pay them to sort out the rough running on top of what you've told them to do.
__________________
![]() Last edited by Dave20046; 17-01-10 at 03:03 PM. |
![]() |
![]() |
![]() |
#4 |
Member
Mega Poster
Join Date: Jul 2003
Location: Doncaster, oop norf
Posts: 2,128
|
![]()
Cleaning the carbs is something you can do yourself, balancing isn't hard but you need good gauges. Don't get suckered by ultrasonic carb cleaning, it's a sledgehammer to crack a nut and is way too expensive. BTW balance the carbs last, you need to do the tappets, air filter, etc. first and also check the chokes aren't sticking (classic problem).
|
![]() |
![]() |
![]() |
#5 |
Member
Mega Poster
Join Date: Jul 2008
Location: Sheffield
Posts: 10,274
|
![]()
I thought this but, if it's a first time, carb cheese bolts might destroy the will to ever work on a bike again
![]()
__________________
![]() |
![]() |
![]() |
![]() |
#6 |
Member
Join Date: May 2006
Location: Newcastle
Posts: 872
|
![]()
Anyone got a carb balance gauge thing in the north west I can test mine with when it's back on the road?
|
![]() |
![]() |
![]() |
#7 | |
Member
Mega Poster
Join Date: Jul 2008
Location: Sheffield
Posts: 10,274
|
![]() Quote:
There are guides on the net of how to make a hydro one, but was a bit too much farting around for me.
__________________
![]() |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SV curvey with 30HP after carb clean!? Grounded! :( | F16Falcon | SV Talk, Tuning & Tweaking | 12 | 07-09-09 03:18 PM |
Poor running after carb balance. | hallasv | SV Talk, Tuning & Tweaking | 14 | 07-08-09 06:04 PM |
Carb balance question-applying vacuum | Old Git | SV Talk, Tuning & Tweaking | 9 | 07-07-09 11:51 AM |
Clean!! its soo clean!! + chain question | John 675 | Photos | 13 | 07-03-09 07:14 PM |
Carb Balance and Service | Scoobs | Bikes - Talk & Issues | 1 | 19-02-05 10:56 PM |