SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
hi all been a member 4 a while now but never posted anything. i have a oil leak coming from my clutch cover it seems i need a new seal its a big o ring does anyone know if and where these r availible. thanks
|
![]() |
![]() |
#2 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
![]()
Seal is probably fine, it is the cover itself that warps.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
![]() |
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
![]() |
![]() |
![]() |
#4 |
Member
Mega Poster
Join Date: Jul 2003
Location: W Mids
Posts: 2,037
|
![]()
Yes & Suzuki.
It seems sometimes however the problem is the cover itself has warped and a new O-ring will do nothing, in which case you either need to swap the entire thing for a pointy cover or replace the cover. Worth mentioning you should also be careful how you tighten it, should always tighten opposite bolts and a bit at a time. Working in a star kind of pattern like this. ![]() Druid
__________________
'00 SV700S - '94 RVF400R - '97 RVF400R - '88 VFR750F |
![]() |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]()
thanks 4 advise will have a look around
|
![]() |
![]() |
#6 |
Guest
Posts: n/a
|
![]()
Just use some gasket maker ontop and around the oring.
|
![]() |
![]() |
#7 |
Member
Join Date: May 2006
Location: Newcastle
Posts: 872
|
![]()
And not over torque them and snap a bolt off like i did. Just a bit tighter, just a bit more, snap - ****!
|
![]() |
![]() |
![]() |
#8 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
![]()
Overtightening can cause leak in first place
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
![]() |
![]() |
![]() |
#9 |
Member
Join Date: May 2006
Location: Newcastle
Posts: 872
|
![]()
yep 10nm if memory serves for those bolts - it's one of those that you remember after doing it
|
![]() |
![]() |
![]() |
#10 |
Guest
Posts: n/a
|
![]()
might b a good idea for me 2 get a small torque wrench then. i have a big 1 that i use 4 the rear wheel but doesn't go low enough for the smaller stuff
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
rocker cover seal | noob-saibot | SV Talk, Tuning & Tweaking | 5 | 29-01-09 09:34 PM |
The never ending clutch cover oil leak | badger-666 | SV Talk, Tuning & Tweaking | 3 | 20-02-08 07:25 PM |
leak from right-hand crankcase/side cover- common problem ? | chriskk | SV Talk, Tuning & Tweaking | 9 | 09-10-07 11:27 AM |
Curvy SV650 clutch cover oil leak | bugsy46 | Bikes - Talk & Issues | 1 | 06-04-07 11:28 PM |
Oh dear- leak from front sprocket shaft seal? | northwind | SV Talk, Tuning & Tweaking | 12 | 12-05-05 02:47 PM |