![]() |
#211 |
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,569
|
![]()
update:
the material is to thick to follow the profile of the swingarm properly. we tried our best and even made new tool but to no avail. it's creasing it at the correct points but is unable to flatten at the bottom, to do this we would have to invest a couple of £k on the proper blades so no way. anyway here is the formed pieces... ![]() they are very very tight on the swingarm/spindle. Lance |
![]() |
![]() |
![]() |
#212 |
Guest
Posts: n/a
|
![]()
Looks fantastic! Can't wait to get a set of these.
Last edited by federer; 28-05-12 at 04:57 PM. |
![]() |
![]() |
#213 |
Guest
Posts: n/a
|
![]()
Does that means this is a no-go? If so then I appreciate the effort mate. It would have been nice to get one up on Suzuki!
|
![]() |
![]() |
#214 |
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,569
|
![]()
it's still a go.
i was just pointing out the fact that the bottom radius will not match the swingarm how i planned it so will be more of a rounded profile but with creases in the correct place. this wont detract from the strength of them it's just they wont look 'perfect' to the 45degree on the bottom and will have what looks like a small gap at the radius. it will still 'grip' the corners. Lance p.s. i'll try and get a pic up later of them on the swingarm. |
![]() |
![]() |
![]() |
#215 |
Guest
Posts: n/a
|
![]()
Ok, good man.
|
![]() |
![]() |
#216 |
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,569
|
![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#217 |
Guest
Posts: n/a
|
![]()
Looks fine for me.
|
![]() |
![]() |
#218 |
Member
Mega Poster
Join Date: Jul 2006
Location: Dundee
Posts: 4,414
|
![]()
Can't say I'm too worried about that
![]() If anything I reckon it'll look better with a single radius bend |
![]() |
![]() |
![]() |
#219 |
Member
Mega Poster
Join Date: Jun 2008
Location: West Lancs
Posts: 4,055
|
![]()
C'mon Lance, get them made up and posted out
![]() |
![]() |
![]() |
![]() |
#220 |
Guest
Posts: n/a
|
![]()
Yea looks boss get em done!!!
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
potential pointy ecu restrictor kit bargain | haydensv650 | Stuff Wanted | 0 | 18-08-11 07:40 PM |
Replacement chain adjuster plates? | SV400Rob | SV Talk, Tuning & Tweaking | 13 | 02-02-11 09:30 PM |
chocolate chain adjuster plates | dmracing | SV Talk, Tuning & Tweaking | 6 | 01-08-09 09:23 PM |
Chain adjuster plates | dmracing | Stuff Wanted | 6 | 24-07-07 05:54 PM |
Stainless adjuster plates.....................bling | svrash | SV Talk, Tuning & Tweaking | 19 | 23-04-06 07:22 PM |