Potential pointy Adjuster Plates Group Buy

Put me down for a set!

No..Name................Type....................Po st to
1...joshwalker094.......Non-Scottoiler, with hole - Post to Nobbylad
2...DarrenSV650S........Scottoiler, not bothered if it has a hole or not
3...Epic Monkey.........
4...MJC-DEV.............Non-Scottoiler
5...Nobbylad............Scottoiler, with markers - Post to Nobbylad
6...muzikill............
7...The Guru............Non-Scottoiler. With markers
8...The Guru............Non-Scottoiler. With markers
9...fluffer.............Non-Scottoiler
10..Kilted Ginger.......
11..Turner..............
12..Jayneflakes.........
13..SIII................
14..peterco.............
15..tetol...............
16..twinset.............Non-Scottoiler
17..Davy.h..............??
18..Speedy..............Non-Scottoiler
19..Shawthing...........Non-Scottoiler. With markers - Post to Nobbylad
20..Sputnik.............
21..Elliott Woodruff....Non-Scottoiler - Post to Nobbylad
22..Steve_God...........Scottoiler version - Post to Nobbylad
23..SirBarnz............Non-Scottoiler
24..federer
25.originlabs..........Non-Scottoiler. With Markers

[Bibio]

thanks so far everyone.

polished SS, if the price is right then i could look into it. i know you can get dull one side and bright the other so it's a possibility.

extra length for the scottoiler pipework. i have straight connectors and tubing lying around which i will supply for people wanting the scottoiler version.

i will also supply the 8mm nut'n'bolt for attachment of the scottoiler bracket so you can attach the scottoiler bobbin bracket.

*** for sake of ease every bracket will have a bottom marker view hole *** just not as big as the original.

i will NOT supply the scottoiler bobbin bracket. but these are readily available form scottoiler and are always supplied in their universal kit. most people use this bracket if they have a scottoiler fitted anyway.

[Nobbylad]

Is 35 definitely the cut-off Lance? 25 is good going for a couple of days, however I'm thinking 35 might still be a push (happy to be proven wrong though!).

[Bibio]

i'll do some sums and get back to everyone.

i don't mind being left with a few to sell on the bay or on svrider so it's getting near the possibility. as you can understand it's all about cash flow.

I'm happy to throw payment your way if I see you on Sunday.

[Bibio]

Originally Posted by The Guru

I'm happy to throw payment your way if I see you on Sunday.

nice offer but...

i would rather wait. its a case of offsetting the amount i have to receiving back again. in as short a time possible. so once they have been cut to getting posted is the time i need to put the cash back into my account.

[Nobbylad]

I'm happy to pay in advance and wait upto a month for delivery if that helps.

[embee]

I like the cut of your jib, young man!

If it's of any use, I made a pair for my curvey because the std items are so flexible. I used 5mm stainless, but because the wheel spindle doesn't have a lot of spare length I counterbores them a little (1.5mm or so) to recess the head and nut into them. This actually looks better and I used a thin s/s washer under the nut which can be sacrificial to some extent, I'll replace it if/when it gets scrawped (technical term!).

The bores are different (hence the markings), the brake side goes on the plain part of the spindle. 17mm I think, while the chain side is on the thread, 16mm. I made them a "decent" fit (you know what I mean).

[Bibio]

that's a nice job embee.

i take it the 5mm is the recess hight from the bottom of the trough to the top edge before it falls away on the angle?

[Bibio]

ok i have done a few sums. from 25 people onwards i will start the ball rolling and do them for the original price of £12. the rest i can sell on the bay at an inflated price to offset the waiting time.

sooooo. i'll get a move on with this and hopefully you should all have them in your grubby paws within a month.