svbits.co.uk showcase - Page 9 - SV650.org

03-02-15, 10:39 PM

Hey mate, can you enlighten me about your front end swap speedo kit? I hope its about a mod for doing a gixxer fork replacement, and not for some tight black budgie smugglers!!😂

Bibio · 03-02-15, 10:46 PM

heheheeee. yup its a speedo drive conversion that runs off the back sprocket. as we all know that when you swap out the front on an SV for a gsxr one it looses the facility of the speedo drive so my kit will give you what you need to get a working speedo again.

its all plug and play with no messing about, has been fully tested for the past 3 years and is rock solid.

Bibio · 03-02-15, 11:04 PM

Quote:

Originally Posted by Jayneflakes

I shall be watching this thread with interest.

i would hope its a bit more than watching

Jayneflakes · 03-02-15, 11:32 PM

Quote:

Originally Posted by Bibio

i would hope its a bit more than watching

When you are a multimillionaire and have your own private jet (painted up like a pointy as it should be), you must fly down here for a cuppa.

In the mean time, I wish you every success.

maviczap · 04-02-15, 10:30 AM

Quote:

Originally Posted by Bibio

Update:

i have been board out my skull recently so i have got my arz in gear and making parts again.

front end swap speedo kits will be available very soon (within 3 weeks) the test kit is going out Thursday to see how a member gets on installing it.

websh!ite will be back up again soon.

Lance

Keep me posted, as I would like to improve the functional, but butt ugly speedo conversion that I've got

04-02-15, 10:40 AM

Quote:

Originally Posted by Bibio

Update:

Gizmos in stock parcelled up ready to post out.

Please can I have one?

Not sure if my PM reached you.

Bibio · 24-02-15, 01:17 PM

well thats the pointy front end conversion speedometer drives almost ready and will be in my grubby paws this time next week all finished and ready to send out to folk that are interested.

as for the curvy well lets just say it's going to have to be a complete redesign apart from the rotor. i was hoping to use the sensor down stand from the pointy but thats looking like a no go. i'll try and get something for the curvy for the summer but dont hold your breath as i'll need to get funds back into the kitty first. i might just start with the adjuster plates and work from there, i was hoping to punch them out on the punch press but at 4mm SS the machine wont like it so its laser cutting again.

i also have 18 Gizmo kits ready to post off.

TamSV · 24-02-15, 02:08 PM

Ah well. I'll need to wait then.

Darren did a nice tidy job on the pointy. It's the total lash up I did on the curvy that needs sorting.

DarrenSV650S · 24-02-15, 04:19 PM

Oh I should mention Tam, be careful when you remove the mudguard bolts. There are a few washers spacing out the speedo sensor plate

25-02-15, 09:40 PM

I'm interested in a speedo kit, need change my rotors so wana to get rid of the magnets!

Any adjuster plates? shredded 3 pairs...

03-02-15, 10:39 PM	#81
scotty217 Guest Posts: n/a	Re: svbits.co.uk showcase Hey mate, can you enlighten me about your front end swap speedo kit? I hope its about a mod for doing a gixxer fork replacement, and not for some tight black budgie smugglers!!😂

03-02-15, 10:46 PM	#82
Bibio Member Mega Poster Join Date: Jul 2008 Location: here as devil's advocate Posts: 11,569	Re: svbits.co.uk showcase heheheeee. yup its a speedo drive conversion that runs off the back sprocket. as we all know that when you swap out the front on an SV for a gsxr one it looses the facility of the speedo drive so my kit will give you what you need to get a working speedo again. its all plug and play with no messing about, has been fully tested for the past 3 years and is rock solid.

24-02-15, 01:17 PM	#87
Bibio Member Mega Poster Join Date: Jul 2008 Location: here as devil's advocate Posts: 11,569	Re: svbits.co.uk showcase well thats the pointy front end conversion speedometer drives almost ready and will be in my grubby paws this time next week all finished and ready to send out to folk that are interested. as for the curvy well lets just say it's going to have to be a complete redesign apart from the rotor. i was hoping to use the sensor down stand from the pointy but thats looking like a no go. i'll try and get something for the curvy for the summer but dont hold your breath as i'll need to get funds back into the kitty first. i might just start with the adjuster plates and work from there, i was hoping to punch them out on the punch press but at 4mm SS the machine wont like it so its laser cutting again. i also have 18 Gizmo kits ready to post off.

24-02-15, 02:08 PM	#88
TamSV Member Mega Poster Join Date: Feb 2010 Location: Troon, Ayrshire Posts: 1,812	Re: svbits.co.uk showcase Ah well. I'll need to wait then. Darren did a nice tidy job on the pointy. It's the total lash up I did on the curvy that needs sorting.

24-02-15, 04:19 PM	#89
DarrenSV650S Member Mega Poster Join Date: Jul 2006 Location: Dundee Posts: 4,414	Re: svbits.co.uk showcase Oh I should mention Tam, be careful when you remove the mudguard bolts. There are a few washers spacing out the speedo sensor plate

25-02-15, 09:40 PM	#90
MarkandSteele Guest Posts: n/a	Re: svbits.co.uk showcase I'm interested in a speedo kit, need change my rotors so wana to get rid of the magnets! Any adjuster plates? shredded 3 pairs...