SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
|
Thread Tools |
13-08-06, 01:59 PM | #11 |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
Yup, we're very aware of the results- just rather short on alternatives. Either of your worst cases don't preclude further invasive action to repair though, so we're going to keep an eye on it and if wear is rapid, go further. Hopefully won't be neccesary though.
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
13-08-06, 04:19 PM | #12 |
Guest
Posts: n/a
|
Maybe a stupid question, but are you sure it's not the shock that's not straight?? Have you tried to put the original shock back in?
|
13-08-06, 04:43 PM | #13 |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
Ah, the post that had the measurements in has dropped off, hang on... The spacer alone is w31.9mm, but the "slot" at the point where the bolt goes through is just 32.19mm across- the washers are just shy of 1mm each so the gap's definately smaller than the linkage etc. By a fair bit, as well. The frame gap should be 34mm across, according to TWF So no doubt but that's where the problem is.
Glad it's not my bike
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
14-08-06, 11:20 AM | #14 |
Guest
Posts: n/a
|
I think you might find the linkage is the wrong way round.
And no dont go cutting the frame...and yes you do need the spacers |
14-08-06, 11:29 AM | #15 | |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
Quote:
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
|
14-08-06, 11:54 AM | #16 |
Guest
Posts: n/a
|
Steve read your question and said it is possible to get it the wrong way round.
Upto you if you want to have a look..only a suggestion |
14-08-06, 12:00 PM | #17 |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
I can assure you it's not, the "thick end" doesn't fit into the shock clevis... I do appreciate the effort but we're way past that point.
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
14-08-06, 12:53 PM | #18 |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
Ah, apologies, I just realised that some of the posts that are now missing would have clarified matters for you, I was presuming you'd have seen them but probably not now, hence my snippy reaction...
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
14-08-06, 01:30 PM | #19 |
Guest
Posts: n/a
|
no i hadnt seen them...
|
14-08-06, 01:51 PM | #20 |
Moderator
Mega Poster
Join Date: Jan 2004
Location: In the garage where I belong
Posts: 17,082
|
That makes more sense then... Confusing, this missing posts lark. I went and posted a reply to one of Coolgirl's posts that isn't there any more, gave me the general demeanor of a tramp shouting at a lamp-post.
__________________
"We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed" |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rear suspension linkage spreadsheet | erik | SV Talk, Tuning & Tweaking | 1 | 22-02-09 09:03 AM |
swinging arm suspension linkage bearings | 21QUEST | SV Talk, Tuning & Tweaking | 13 | 05-08-08 01:40 PM |
Suspension Linkage | Grinch | Stuff Wanted | 21 | 18-04-07 01:19 PM |
Suspension Linkage - Curvy | 21QUEST | SV Talk, Tuning & Tweaking | 5 | 13-06-06 11:17 AM |
Got me stumped???? | rictus01 | Bikes - Talk & Issues | 15 | 01-05-06 11:45 PM |