 |
 |
| Bikes - Talk & Issues Newsworthy and topical general biking and bike related issues. No crapola! Need Help: Try Searching before posting |
 |
|
|
Thread Tools |
24-06-15, 05:20 PM
|
#1 |
|
Member
Join Date: May 2015
Posts: 113
|
Dealer mode activation sensor cut wires?!?
Hi I just made a dealer mode switch to check my bike as it's still not right but it didn't work. On closer inspection the back of the sensor has had 2 wires cut by someone at some stage?!? Why would someone do this?
|
|
|
|
24-06-15, 05:52 PM
|
#2 |
|
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,540
|
Re: Dealer mode activation sensor cut wires?!?
Black/White is ground and Orange/Green in ignition live power so i would presume to wire an alarm or gear change indicator at some point.
on closer inspection to the wiring diagram they both go back to the ECU so have a look at the ECU and trace back which should let you find the other ends. Last edited by Bibio; 24-06-15 at 06:01 PM. |
|
|
|
|
24-06-15, 05:54 PM
|
#3 |
|
Member
Join Date: May 2015
Posts: 113
|
Re: Dealer mode activation sensor cut wires?!?
Okay thanks for your response. Does that mean that I cannot get the fault codes up now then?
|
|
|
|
|
24-06-15, 06:03 PM
|
#4 |
|
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,540
|
Re: Dealer mode activation sensor cut wires?!?
not unless you join the wires again. i would say just take the black/white to ground but i fear that it might do damage or it needs to route via the ECU to be active.
|
|
|
|
|
26-06-15, 05:05 PM
|
#5 |
|
Member
Join Date: May 2015
Posts: 113
|
Re: Dealer mode activation sensor cut wires?!?
Does anyone know how I can adjust the tps without the dealer mode as obviously that method is not possible now
|
|
|
|
|
26-06-15, 06:06 PM
|
#6 | |
|
The Sick Man
Mega Poster
Join Date: Nov 2004
Location: Peckham.SE.LDN
Posts: 4,768
|
Re: Dealer mode activation sensor cut wires?!?
Quote:
You only need the ground so you could efectivly just touch the wire between the White/Red (bottom right) and the chasis. All the wires go back to the ECU (depending on the year) so suspect the others are programming wires looking at the diagrams over the years.
__________________
OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions |
|
|
|
|
|
26-06-15, 06:09 PM
|
#7 |
|
Member
Join Date: May 2015
Posts: 113
|
Re: Dealer mode activation sensor cut wires?!?
Oh okay so if I create a longer dealer mode button and put one end into the hole that isn't cut and then the other to the frame then it would work?
|
|
|
|
|
28-06-15, 02:32 PM
|
#8 |
|
Member
Join Date: May 2015
Posts: 113
|
Re: Dealer mode activation sensor cut wires?!?
I can't find for the life of me where the wires has been used after ir was cut?!? I really want to adjust the tps it's driving me mad
|
|
|
|
|
28-06-15, 11:11 PM
|
#9 |
|
Member
Mega Poster
Join Date: Jul 2008
Location: here as devil's advocate
Posts: 11,540
|
Re: Dealer mode activation sensor cut wires?!?
it goes back to the ECU.. see post #2
|
|
|
|
|
26-11-21, 10:08 AM
|
#10 |
|
Junior Member
Join Date: Nov 2021
Posts: 2
|
Re: Dealer mode activation sensor cut wires?!?
Hello my man. I’ve just gone to put my bike into dealer mode and found that my connector block is cut the same as yours. Did you find a solution to be able to put yours into dealer mode? I have the FI light showing but as mine is cut the same as yours I’m not sure what today. Thank you in advance
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Dealer Mode Connector | Stuart42 | Stuff Wanted | 4 | 24-03-15 07:03 PM |
| Dealer mode connector 2013 SV - where? | Soapysoap | SV Talk, Tuning & Tweaking | 3 | 23-09-14 08:59 AM |
| check, no start, meta alarm, cant dealer mode | davepreston | SV Talk, Tuning & Tweaking | 48 | 21-03-11 06:02 PM |
| Crash.NET - Sensor failure puts Capirossi in 'safe mode' | NewsBot | News | 0 | 05-10-09 03:20 PM |
| How do you put the bike in dealer fault mode? | rowdy | SV Talk, Tuning & Tweaking | 7 | 31-01-09 09:07 AM |
