SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
|
Thread Tools |
26-04-06, 09:36 PM | #1 |
Guest
Posts: n/a
|
Am i missing a spacer?
Hi,
Just got new michelin pilot powers fitted onto my 2005 Sv650. Went to fit the rear wheel back on but as i tightened the nut on the spindel the wheel also tightens, eventually locking solid. I noticed a spacer on the sprocket side but no spacer on the brake calliper side. Question is...am i missing a spacer from the brake caliper side? Should there be a spacer on both sides of the wheel? Can anyone help please? Many Thanks Mark |
26-04-06, 09:37 PM | #2 |
Guest
Posts: n/a
|
Without checking facts 100% and never having owned said vehicle I say yes and the fact checkers be damned.
|
26-04-06, 09:39 PM | #3 |
Guest
Posts: n/a
|
assuming it's the same as a K4 then yes, there should be a spacer both sides.
|
26-04-06, 09:39 PM | #4 |
Guest
Posts: n/a
|
There should be a spacer on the caliper side, yes. On the curvey definitely, Can't say for definite on the pointy, but I imagine it's the same.
It looks similar to a cotton reel.. Maybe someone will nicely post up a pic for you?? Did you take wheel off, or garage?? |
26-04-06, 09:42 PM | #5 |
Guest
Posts: n/a
|
Also, just how far did you tighten the bolt. Did the swingarm get bent in?
Maybe check that it's not bent in to much if this is the case.. |
26-04-06, 10:06 PM | #6 |
Guest
Posts: n/a
|
Right so it must have gone missing somewhere! My dad and I removed the wheel before i gave it a clean and took to garage...however cant see any spacers along my path. Took the bike into a garage to get them to fit the new michelins so maybe thinking it fell out in there?
KciN: Picture would be great if anyone has but reckon i know what it is roughy . Swingarm did not get bent in was only tightened by hand. It looks like part of the brake caliper is rubbing against the brake disk. The spacer should be between the brake caliper and the wheel if i am correct in thinking? Got me confused and annoyed now...been off road for a week now and i want to try out my new powers |
26-04-06, 10:08 PM | #7 |
Guest
Posts: n/a
|
Meant to add:
How much would the spacer cost from a dealer? and would they be likely to have them in stock? Will also take a look around my garage and garden for the spacer in the light, maybe, just maybe will find it lying about! Thanks for the help! Mark |
26-04-06, 10:14 PM | #8 |
Guest
Posts: n/a
|
Suzuki dealer would have them in stock if they're any good. I know the spacer for inside a bandit 12 wheel cost about £9, so maybe...
|
26-04-06, 10:17 PM | #9 |
Guest
Posts: n/a
|
Ok hopefully they will have one in then! Shall give my local(ish) dealer a phone tomorrow morning and if in stock shall pop up and collect! Hopefully that shall solve my problem
Thanks again! |
26-04-06, 10:17 PM | #10 |
Guest
Posts: n/a
|
There sould be a spacer on the calliper side it is shaped like a mushroom!!!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help ,spacer ,where From ? | redbiker 954 | Mini-Twins | 6 | 16-03-08 04:13 PM |
Speedo drive replacement spacer? | Sideshow#36 | Stuff Wanted | 0 | 20-09-07 10:54 PM |
Wheel spacer dilemma.... | haggis | SV Talk, Tuning & Tweaking | 8 | 08-03-07 11:30 PM |
Rubber Mirror Spacer | Saucerboy | Stuff Wanted | 2 | 26-12-06 05:35 PM |
Spacer kit to fit B12 rear wheel | northwind | SV Talk, Tuning & Tweaking | 5 | 28-03-06 07:03 PM |