SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
|
Thread Tools |
30-06-06, 03:15 AM | #1 |
Guest
Posts: n/a
|
Idle adjust screw?
Am having problems with my 2000 SV idling too slowly.
Apparently there is an "idle adjust screw" located somewhere on the left side of the bike and if I tighten it then I can raise the idle speed? Is this correct?? If it is correct, could anyone shed some light on what this screw looks like, I cannot see anything that looks like it would be an adjustable screw. Any help would be greatly appreciated. Thanks. |
30-06-06, 06:07 AM | #2 |
Guest
Posts: n/a
|
If it's a curvey you're looking for a black knob about 20mm in dameter with a ridged edge. IRC it's between the two main frame tubes
Don't know about the pointies Tris |
30-06-06, 07:04 AM | #3 | |
Vipers Pillion Bitch
Mega Poster
Join Date: Jul 2003
Location: Waterlooville
Posts: 3,933
|
Quote:
Although you may find if it's never been touched or not touched for a long time it may not work very well. If this is the case you will need to get the tank up and possibly get the air box off to access the adjuster from the carb end. Easy to do but just time consuming. Hopefully the little black adjuster knob will work.
__________________
I look good, I mean really good! Hey everyone come and see how good I look! |
|
01-07-06, 02:26 AM | #4 |
Guest
Posts: n/a
|
idle adjust?
So, is this a plastic knob with ridges? Is there a cable going into it?
What do I do, tighten it? Thanks |
01-07-06, 01:26 PM | #5 |
Guest
Posts: n/a
|
with the engine running turn it one way or the other until you have the desired idle speed
|
01-07-06, 01:29 PM | #6 |
Guest
Posts: n/a
|
looking at it, turning it clockwise will increase the revs, anticlockwise the revs will drop. And yes the plastic knob with ridges. It does tend to sieze up, but little dab of engine oil to lubricate should do the trick.
|
01-07-06, 02:53 PM | #7 |
Member
Mega Poster
Join Date: Jul 2003
Location: Warwickshire
Posts: 2,801
|
The knob connects to the throttle stop screw by a length of flexible drive (like curtain wire), so you'll feel it being a little "springy".
The thread up at the carb end might be stiff, that's where you need the lube. If the knob doesn't turn easily, or it feels like something's going to break, don't force it. You'll need to lift the tank and airbox to get to it to clean/lube as required, not a difficult task. Set the idle when it's at normal running temperature, and make sure the choke is fully off. It's sometimes easier to adjust it by turning it up too high then backing off rather than gently easing it upwards fractions at a time, the springy drive tends to wind-up a bit. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Idle Adjuster Screw | mattglavin | SV Talk, Tuning & Tweaking | 11 | 11-10-07 12:37 PM |
Cant adjust the Idle nob | TSM | SV Talk, Tuning & Tweaking | 7 | 29-04-05 04:02 PM |
Bloody idle screw! | Mervin | SV Talk, Tuning & Tweaking | 16 | 04-02-05 08:00 AM |
Should I adjust my levers or not? - Confused | Round | SV Talk, Tuning & Tweaking | 2 | 06-10-04 01:06 PM |