Meta Alarm Removal - SV650.org

15-09-08, 11:09 AM

I've run into a problem with stripping the bike down. The alarm unit wires pass through a hole in the subframe and rear mudguard. Obviously it is too big to go through and the wires disappear into the loom. I don't really want to cut it off, not least of all because I reckon it'll set the alarm off. Any tips guys?

15-09-08, 12:10 PM

Can you open the alarm unit up and disconnect it more easily in there? Otherwise I think....you don't really have any choice - well, unless the other end of the loom will fit through the hole (so you can pull all the wiring through the other way).

15-09-08, 01:12 PM

you may well have to open up the loom and un wire the alarm back to the unit, or weigh up whats worth more the sub frame or alarm and loom?? and then sacrifice one or tother?

TSM · 15-09-08, 01:14 PM

most meta alarms have a connector at the bottom, take it off and you may just squeese it though, ive seen this several times with people that have meta alarms, grr annoying

15-09-08, 09:50 PM

Yes TSM it has got a connector but it won't go through the access holes I'm sure, although I will try tomorrow. Rather looks like the alarm was placed first then the wires pushed through.

Thanks chaps

15-09-08, 11:09 AM	#1
petevtwin650 Guest Posts: n/a	Meta Alarm Removal I've run into a problem with stripping the bike down. The alarm unit wires pass through a hole in the subframe and rear mudguard. Obviously it is too big to go through and the wires disappear into the loom. I don't really want to cut it off, not least of all because I reckon it'll set the alarm off. Any tips guys?

15-09-08, 12:10 PM	#2
muffles Guest Posts: n/a	Re: Meta Alarm Removal Can you open the alarm unit up and disconnect it more easily in there? Otherwise I think....you don't really have any choice - well, unless the other end of the loom will fit through the hole (so you can pull all the wiring through the other way).

15-09-08, 01:12 PM	#3
454697819 Guest Posts: n/a	Re: Meta Alarm Removal you may well have to open up the loom and un wire the alarm back to the unit, or weigh up whats worth more the sub frame or alarm and loom?? and then sacrifice one or tother?

15-09-08, 01:14 PM	#4
TSM The Sick Man Mega Poster Join Date: Nov 2004 Location: Peckham.SE.LDN Posts: 4,768	Re: Meta Alarm Removal most meta alarms have a connector at the bottom, take it off and you may just squeese it though, ive seen this several times with people that have meta alarms, grr annoying __________________ OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions

15-09-08, 09:50 PM	#5
petevtwin650 Guest Posts: n/a	Re: Meta Alarm Removal Yes TSM it has got a connector but it won't go through the access holes I'm sure, although I will try tomorrow. Rather looks like the alarm was placed first then the wires pushed through. Thanks chaps

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
what alarm should i get datatool or meta	zsv650	SV Talk, Tuning & Tweaking	24	23-09-08 10:52 PM
Meta Alarm Technician	plowsie	Bikes - Talk & Issues	3	31-05-07 09:12 PM
Meta alarm sytsems	plowsie	Bikes - Talk & Issues	1	04-04-07 04:00 PM
Meta Alarm Help!!!	Samurai	Bikes - Talk & Issues	5	09-02-06 02:52 PM
meta alarm problems	jonc	Bikes - Talk & Issues	11	07-02-06 07:17 PM