Pointy won't start after datatool S4 removal - Page 2 - SV650.org

DJ123 · 25-03-14, 09:13 PM

What about the 4 wires which are the factory fit alarm connector?

25-03-14, 09:14 PM

Can't find them, i think they've been removed?

DJ123 · 25-03-14, 09:20 PM

They run into a 4 way connector (similar to the fault code block). Should be in the same loom on the left hand (looking towards the front of the bike) side of the bike (rear panel)

25-03-14, 09:27 PM

Is it a small square whitish connector with mostly black cables that run to the indicators???

DJ123 · 25-03-14, 09:37 PM

They are in 1, there's more

25-03-14, 10:30 PM

Right, pics for clarity now!

So, this is the 3 to one orange and green wire splicing that doesn't appear to be standard.

The left orange and green cable comes from the fuse box, splits into three (that's where it looks dodgy) and one goes to the resistor, the other two look as if they go towards the front of the bike?

This is where part of the alarm wiring had been spliced in, its the Mode select switch connector. I've connected it temp (before soldering) and still no digital display or fuel pump. (look at orange and green wire)

Is this the Alarm connector? One of the wires had been chopped into the alarm wiring. This one is position on the LHS behind the battery in line with the rest of the loom

This is a similar box, in the same place but level with the battery, don't think this one was spliced into.

Or is this the alarm connector?

muzikill · 29-03-14, 01:00 PM

Really, a colour wiring diagram will support your fault finding. Its difficult doing it this way over the internet without someone being present to go through all the colours.

Sent from my GT-I9505 using Tapatalk

25-03-14, 09:13 PM	#11
DJ123 Member Mega Poster Join Date: Jul 2011 Location: Somewhere over there Posts: 3,245	Re: Pointy won't start after datatool S4 removal What about the 4 wires which are the factory fit alarm connector? __________________ BMW F800ST

25-03-14, 09:14 PM	#12
Mikey360 Guest Posts: n/a	Re: Pointy won't start after datatool S4 removal Can't find them, i think they've been removed?

25-03-14, 09:20 PM	#13
DJ123 Member Mega Poster Join Date: Jul 2011 Location: Somewhere over there Posts: 3,245	Re: Pointy won't start after datatool S4 removal They run into a 4 way connector (similar to the fault code block). Should be in the same loom on the left hand (looking towards the front of the bike) side of the bike (rear panel) __________________ BMW F800ST

25-03-14, 09:27 PM	#14
Mikey360 Guest Posts: n/a	Re: Pointy won't start after datatool S4 removal Is it a small square whitish connector with mostly black cables that run to the indicators???

25-03-14, 09:37 PM	#15
DJ123 Member Mega Poster Join Date: Jul 2011 Location: Somewhere over there Posts: 3,245	Re: Pointy won't start after datatool S4 removal They are in 1, there's more __________________ BMW F800ST

25-03-14, 10:30 PM	#16
Mikey360 Guest Posts: n/a	Re: Pointy won't start after datatool S4 removal Right, pics for clarity now! So, this is the 3 to one orange and green wire splicing that doesn't appear to be standard. The left orange and green cable comes from the fuse box, splits into three (that's where it looks dodgy) and one goes to the resistor, the other two look as if they go towards the front of the bike? This is where part of the alarm wiring had been spliced in, its the Mode select switch connector. I've connected it temp (before soldering) and still no digital display or fuel pump. (look at orange and green wire) Is this the Alarm connector? One of the wires had been chopped into the alarm wiring. This one is position on the LHS behind the battery in line with the rest of the loom This is a similar box, in the same place but level with the battery, don't think this one was spliced into. Or is this the alarm connector?

29-03-14, 01:00 PM	#17
muzikill Member Mega Poster Join Date: Jul 2005 Location: Dunfermline Posts: 1,712	Re: Pointy won't start after datatool S4 removal Really, a colour wiring diagram will support your fault finding. Its difficult doing it this way over the internet without someone being present to go through all the colours. Sent from my GT-I9505 using Tapatalk __________________ Learn to maintain your bike, take it apart, rebuild the engine & more (using better bolts ), drop it & fix it again! K3 Job c.v: Engine:remove/split/rebuild/refit. Replace:Gearbox,Fuel pump,Gaskets. Piston clean,rings. Overhaul:Throttle body,Injectors,Brakes,Forks. Remove/refit:Exhaust,Radiator,Oil cooler,Throttle,Air filter,Tank. Replace: Oil,Coolant,grease,brake hoses & bleed.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Datatool alarm removal	thedonal	SV Talk, Tuning & Tweaking	54	24-07-15 06:34 AM
Datatool 3 Removal?	Chris199	Bikes - Talk & Issues	0	15-02-13 11:49 PM
datatool 3 removal?	Gibby	Bikes - Talk & Issues	16	20-06-12 10:59 AM
Removed Datatool 3 now won't start.	Ghosd10	SV Talk, Tuning & Tweaking	4	22-02-11 01:58 PM
Datatool System 3 removal.	Lozzo	SV Talk, Tuning & Tweaking	17	14-05-07 09:42 PM