17-12-14, 10:31 PM | #291 |
Member
Mega Poster
Join Date: Aug 2003
Location: Croydonia
Posts: 5,376
|
Re: What have you tinkered with today?
It's really not any harder than taking your old cams out and putting the new ones in. They can be used one of 2 ways. Like for like all the timing marks are exactly the same on pointy & curvy, so it's no harder than putting your old ones back. The other way is to use 2 sets of inlet cams, which is a little less straight forward. I've not done that as this is for a minitwin, if it was a road bike I'd be more tempted. Clicky.
1) Do one head at a time, the cams are marked INF,EXF,INR,EXR. Put them in the right places. 2) It may be worth getting hold of some K3 cam chain tensioners as well, though it's by no means essential. They really are a much nicer design. 3) Roll the motor over a few times and check the clearances again as you've changed one of the surfaces involved. In my case they were still fine but there you go. 4) Make sure you can get hold of cam chain tensioner gaskets. The front one usually tears. The rear may do too. Jambo
__________________
Modern motorcycles are bloody brilliant, enjoy it while we can |
18-12-14, 06:33 AM | #292 |
Member
Mega Poster
Join Date: Mar 2007
Posts: 9,096
|
Re: What have you tinkered with today?
Sorry my question should have been a bit more precise. I've got that bayareariders blog on the cam swap, cheers.
Any tips on getting the ccts in and out?
__________________
We're riding out tonight to case the promised land Make everyday count RIP Reeder - Jolly Green Giant and comedy genius |
18-12-14, 09:00 AM | #293 |
Member
Mega Poster
Join Date: Aug 2003
Location: Croydonia
Posts: 5,376
|
Re: What have you tinkered with today?
Well, I used a narrow screwdriver and held it in place with a bit of tape but it was a bit of a fiddle. I'm planning on making one of these out of some thin metal as being able to just pull the tab out should free up a load of effort: http://www.svrider.com/forum/showthr...?postid=906763
To remove them i just undo the 5mm headed Allen bolts and let the tensioner extend while undoing Jambo Sent without a real keyboard
__________________
Modern motorcycles are bloody brilliant, enjoy it while we can Last edited by jambo; 18-12-14 at 09:01 AM. |
18-12-14, 04:49 PM | #294 |
Member
Mega Poster
Join Date: Mar 2007
Posts: 9,096
|
Re: What have you tinkered with today?
Ta, I was looking for the info about the CCT tool
__________________
We're riding out tonight to case the promised land Make everyday count RIP Reeder - Jolly Green Giant and comedy genius |
18-12-14, 05:09 PM | #295 |
Member
Mega Poster
Join Date: Aug 2003
Location: Croydonia
Posts: 5,376
|
Re: What have you tinkered with today?
I made a simple tool up today with a used can and some tin snips. 10 minutes well spent and reinstalling the front CCT was much easier with it in place.
Jambo Sent without a real keyboard
__________________
Modern motorcycles are bloody brilliant, enjoy it while we can |
06-01-15, 08:35 AM | #296 |
Guest
Posts: n/a
|
Re: What have you tinkered with today?
Fitted my MTC exhaust sounds sweat as a nut fitted my shortened levers, Tail tidy and rear wheel hugger starting to put my own wee stamp on her.
|
06-01-15, 10:50 AM | #297 |
Guest
Posts: n/a
|
Re: What have you tinkered with today?
|
06-01-15, 04:51 PM | #298 |
Guest
Posts: n/a
|
Re: What have you tinkered with today?
|
06-01-15, 05:06 PM | #299 |
Member
Mega Poster
Join Date: Apr 2010
Location: Newcastle upon Tyne, Just south of salad dodging country
Posts: 7,750
|
Re: What have you tinkered with today?
I used araldite and it's been spot on
__________________
RIP Reeder 20/07/1988 - 21/03/2012. Always missed squire!!! Every year we meet old friends, gain some new ones, lose old ones and you always remember them all. “Live as if you were to die tomorrow. Learn as if you were to live forever.” Mahatma Gandhi |
06-01-15, 05:11 PM | #300 |
John T
Mega Poster
Join Date: May 2003
Location: Shrewsbury, Shrops, UK
Posts: 2,455
|
Re: What have you tinkered with today?
__________________
Admin for this forum and the main site. John@sv650.org |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Been got already today.. | 454697819 | Idle Banter | 16 | 01-04-10 02:08 PM |
Today | DaveP | The Border Patrol | 4 | 02-03-10 10:52 AM |
Going out today? | tj2 | The Border Patrol | 1 | 01-06-09 09:22 PM |
Today | Tara | Guildford Massive | 14 | 02-06-08 11:56 AM |
Today...... | Caddy2000 | Idle Banter | 15 | 19-04-06 05:39 PM |