HEL Braided lines - SV650.org

16-05-05, 08:32 PM

Just had a quick look at mine that arrived in the post on Saturday and am a little bit puzzled. (I got the 2F 1R set for a K3)

The rear ones bolts are both facing the same way but looking at the bike it looks like one should be at 90 degrees to the other to allow it to fit?

I'm thinking that both the fronts attach to the master cylinder using the double banjo bolt and use the washers as spacers. That right?

16-05-05, 08:34 PM

Yup.

16-05-05, 08:42 PM

Yup it should be at 90 degrees or yup that's how th fronts work or yup to both?

17-05-05, 01:22 PM

bump...

17-05-05, 01:50 PM

Phoned HEL as I was worried about the banjo's facingthe wrong way. Everything else seems fine.

Was told that by holding the collars tightly and putting something through the banjos that I can rotate them to the deseried degree

Viney · 17-05-05, 02:06 PM

You can turn the ends round, but i would see if you can fit it without doing it! As for your other question. Yes a double banjo though both both ends at the Mstr cyl. Copper washer in between the ends as well as either side

27-05-05, 05:03 PM

Quote:

Originally Posted by Couerdelion

Phoned HEL as I was worried about the banjo's facingthe wrong way. Everything else seems fine.

Was told that by holding the collars tightly and putting something through the banjos that I can rotate them to the deseried degree

Did you end up doing this ?

I just fitted my HEL rear line and had the same problem.
Now it looks a little weird because the line curls up

I'd show a pic, but my camera is unavailable right now.

30-05-05, 07:13 AM

Never mind.

I just did it and it worked.

Although it seems the line is a little longer than the original, so I had to route it a little differently, i.e. turning the banjo at the master cylinder so it points upwards.

it seems to work so far...

16-05-05, 08:32 PM	#1
Couerdelion Guest Posts: n/a	HEL Braided lines Just had a quick look at mine that arrived in the post on Saturday and am a little bit puzzled. (I got the 2F 1R set for a K3) The rear ones bolts are both facing the same way but looking at the bike it looks like one should be at 90 degrees to the other to allow it to fit? I'm thinking that both the fronts attach to the master cylinder using the double banjo bolt and use the washers as spacers. That right?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
braided lines	xbox650	SV Talk, Tuning & Tweaking	23	02-12-08 04:45 PM
Braided lines	yorkie_chris	SV Talk, Tuning & Tweaking	1	31-05-07 09:58 PM
Braided Lines	M65	SV Talk, Tuning & Tweaking	10	26-06-05 02:02 PM
HEL Braided lines	mysteryjimbo	SV Talk, Tuning & Tweaking	8	10-02-05 10:20 PM
Braided Lines	454697819	SV Talk, Tuning & Tweaking	14	08-01-05 03:37 PM

16-05-05, 08:42 PM	#3
Couerdelion Guest Posts: n/a	Yup it should be at 90 degrees or yup that's how th fronts work or yup to both?

17-05-05, 01:50 PM	#5
Couerdelion Guest Posts: n/a	Phoned HEL as I was worried about the banjo's facingthe wrong way. Everything else seems fine. Was told that by holding the collars tightly and putting something through the banjos that I can rotate them to the deseried degree

17-05-05, 02:06 PM	#6
Viney Member Mega Poster Join Date: Jul 2003 Location: In the shadows to the left Posts: 7,700	You can turn the ends round, but i would see if you can fit it without doing it! As for your other question. Yes a double banjo though both both ends at the Mstr cyl. Copper washer in between the ends as well as either side

30-05-05, 07:13 AM	#8
uthaug Guest Posts: n/a	Never mind. I just did it and it worked. Although it seems the line is a little longer than the original, so I had to route it a little differently, i.e. turning the banjo at the master cylinder so it points upwards. it seems to work so far...