SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
|
Thread Tools |
17-11-08, 09:33 AM | #11 | |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
Quote:
Sorry 'bout that Grinch. Dunno why it should make the fan run all the time though. |
|
17-11-08, 09:36 AM | #12 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
Oh this is bugging me, I keep just thinking about it and it so bloody annoying. Bike starts, all is fine... then bike fails to start, have no bike.
|
17-11-08, 09:37 AM | #13 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
|
17-11-08, 10:44 AM | #14 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
After a few PM's with Pete I have e-mailed Meta to check the components and fitting incase there was something I missed, it was Meta M357T alarm.
|
17-11-08, 11:24 AM | #15 |
The Sick Man
Mega Poster
Join Date: Nov 2004
Location: Peckham.SE.LDN
Posts: 4,768
|
Re: Afterswapping the loom out.
What did you miss? Forgot to remove alarm
__________________
OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions |
17-11-08, 11:35 AM | #16 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
Well the alarm was not connected, but cut off so I re-soldered all the joints back together and sealed the loom back up.
I did leave a small cylindrical like resistor in the loom though, as it looked like a noise or surge suppressor. It was no bigger then my thumb so didn't think it was a immobiliser, and only had a single in-line connection. But now I'm wondering so thought I should check with Meta. |
17-11-08, 11:42 AM | #17 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
Ah I think its a diode - Like the second one down -
Would this stop the supply as this is not what I thought a diode would do. |
17-11-08, 12:15 PM | #18 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
Right, this diode should be fine as they are normally put in to stop power spikes from the indicators when the alarm flashes them. So it must be something I knocked when I put the bike together, so looks like I'm striping the bike apart.
|
17-11-08, 12:28 PM | #19 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
have you checked the fuses and or the fuse that will have been wired into the alarm? I cannot recall wether they sit in the alram loom or on the bike loom...
|
17-11-08, 12:39 PM | #20 |
Guest
Posts: n/a
|
Re: Afterswapping the loom out.
I un-wired the alarms fuse.
But good point, I didn't check all the fuses so I could have blown one, I had all the dash lights. Last edited by Grinch; 17-11-08 at 12:45 PM. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
swapping battery with GSX600F | Terence | SV Talk, Tuning & Tweaking | 3 | 10-07-07 09:33 PM |
Swapping Radiators | squirrel_hunter | Bikes - Talk & Issues | 9 | 13-05-07 02:38 PM |
swapping batteries | redeye321 | SV Talk, Tuning & Tweaking | 2 | 29-11-06 08:24 PM |
Swapping headlight bulbs | Jase22 | SV Talk, Tuning & Tweaking | 11 | 21-12-05 12:33 AM |
Swapping the exhaust | mysteryjimbo | SV Talk, Tuning & Tweaking | 2 | 06-10-04 10:48 PM |