SV650.org - SV650 & Gladius 650 Forum



SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000
Need Help: Try Searching before posting

Reply
 
Thread Tools
Old 03-06-13, 10:42 AM   #1
gladius1
Guest
 
Posts: n/a
Default Fitting crash bungs to a Gladius ?

does anybody know how to and how easy crash bimbles are to fit to my gladius ... it will be my first big bike after passing my test ?
  Reply With Quote
Old 03-06-13, 11:21 AM   #2
Bibio
Member
Mega Poster
 
Bibio's Avatar
 
Join Date: Jul 2008
Location: Dreich Fife (its grey and miserable)
Posts: 11,200
Default Re: Fitting crash bungs to a Gladius ?

the thing you are looking for is 'crash bungs' a bimble is a sedate ride on your bike.

i'm sure R&G will sell something and being a naked bike i think they would be pretty simple to fit.
Bibio is offline   Reply With Quote
Old 03-06-13, 11:49 AM   #3
veenee
Member
 
veenee's Avatar
 
Join Date: Oct 2011
Location: Surrey
Posts: 154
Default Re: Fitting crash bungs to a Gladius ?

I bought some cheap(ish) ones on eBay - 'used' them a couple of times and they still seem fine. Were very easy to fit on SV650 naked - should be similar on Gladius
__________________
Z1000SX 2017 Lime Green
ex SV650N K8 Thunder Grey
my snaps
"I will always be puzzled by the human predilection for piloting vehicles at unsafe velocities."
Lt. Cmdr. Data
veenee is offline   Reply With Quote
Old 03-06-13, 06:14 PM   #4
Fruity-ya-ya
Member
 
Fruity-ya-ya's Avatar
 
Join Date: Jan 2010
Location: Sheffield
Posts: 482
Default Re: Fitting crash bungs to a Gladius ?

I bought the r&g aeros with the hole cutter bit direct from r&g rather than digging out the right size from my Dads tool box.

Simple to fit with clear instructions which i read to check the torque after I'd cut the holes in the plastics and hand tightened them up.
Check you do not over tighten or you will be off to the shops for a replacement nut.

Other than that they were not needed, very intuitive.

Saying that I would stress that when marking the plastics make sure to fully tighten them back on as you go or the punch/marking tool will put more than one impression when you use it making it trickier than it need be when cutting (yep i had to refit and remark one side as i was a big head and didn't fasten it on first time - bit of tape to show me the true punch mark did the trick).

Although not needed, I also used a very small drill bit to pilot from the inside to out with a square of masking tape on the outside. I felt it helped stop the cutter from skipping (seemed to help anyway).

The awkward part was getting the bungs aligned as they are tear drop shaped. They spun in alternate directions as i tightened them straddling the tank. Would have been much quicker had i had someone to hold one as i did up the other but I might make myself a wooden prop for next time.
__________________
'15 Yellow Honda CB650F
Smile -
- We're not here for long so be mardy in the next life!
I'd much rather be happy than right any day.

Fruity-ya-ya is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fitting crash bungs, cutting fairings? kellyjo Bikes - Talk & Issues 1 05-05-11 07:12 PM
Fitting Curvy Crash Bungs? Aquila SV Talk, Tuning & Tweaking 8 12-09-10 05:29 PM
Fitting R&G Crash Bungs DanDare SV Talk, Tuning & Tweaking 9 15-01-08 01:45 PM
Help with fitting Motosliders Crash Bungs Catflavor SV Talk, Tuning & Tweaking 6 01-05-07 10:28 AM
Fitting Motrax Crash Bungs Heed SV Talk, Tuning & Tweaking 10 15-02-07 08:30 PM


All times are GMT. The time now is 09:11 AM.


Powered by vBulletin® - Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.