Bikes - Talk & Issues Newsworthy and topical general biking and bike related issues. No crapola! Need Help: Try Searching before posting |
|
Thread Tools |
07-05-11, 07:06 PM | #1 |
Knob faced knobster
Mega Poster
Join Date: Jan 2005
Location: Haslemere
Posts: 5,419
|
GSXR fork settings
Anyone know the base settings for the forks on a GSXR750 SRAD?
I've not ridden the SV in anger since the front end swap. But i would like to check the settings on the forks. So how many twiddles from fully in etc. Ta
__________________
2001 SV650 in shimmerin green, Not broken anymore |
07-05-11, 07:22 PM | #2 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
Re: GSXR fork settings
No point going for stock base settings on unknown forks. Stock is somewhere like 1 1/8 turns out.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat Last edited by yorkie_chris; 07-05-11 at 07:35 PM. |
07-05-11, 07:54 PM | #3 |
Knob faced knobster
Mega Poster
Join Date: Jan 2005
Location: Haslemere
Posts: 5,419
|
Re: GSXR fork settings
I meant stock settings, sorry
__________________
2001 SV650 in shimmerin green, Not broken anymore |
07-05-11, 08:02 PM | #4 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
Re: GSXR fork settings
Strange, I tried to edit that and it just put it back how it was.
Set it for 20mm of static sag, 1.25 on comp and 1 on rebound and ride it.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
08-05-11, 09:30 AM | #5 |
Member
Mega Poster
Join Date: Feb 2010
Location: Troon, Ayrshire
Posts: 1,811
|
Re: GSXR fork settings
Stock SRAD setting are 4 rings of preload, Rebound 1 1/8 turn out and Compression 1 turn out.
I started off with these on the basis that you've got to start somewhere, but they were pretty horrible on the SV. Not as terrible as stock ZX10R setting on the rear shock though. Go with YC's suggestion and set sag first. I've got everything out a bit further than the stock SRAD settings and it's much nicer. Still a work in progress as I can't seem to leave the bike in one piece for very long. |
08-05-11, 11:31 AM | #6 |
Knob faced knobster
Mega Poster
Join Date: Jan 2005
Location: Haslemere
Posts: 5,419
|
Re: GSXR fork settings
Cheers for the answers.
Just need to do a bit of searching to set the sag as I've never needed to do I before
__________________
2001 SV650 in shimmerin green, Not broken anymore |
08-05-11, 11:33 AM | #7 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
Re: GSXR fork settings
Unload front end and measure amount of chrome showing. Say this is 115mm
Then put weight of bike onto it, give it a wiggle, measure again. Add preload until this measurement is 115-x. I'd go 20mm static sag, so in this example you'd want to get the amount of chrome showing to 95mm.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
16-06-11, 09:13 PM | #8 |
Member
Mega Poster
Join Date: Feb 2010
Location: Troon, Ayrshire
Posts: 1,811
|
Re: GSXR fork settings
I have a confession - I'm a div. I've got too many manuals and too many bits of too many bikes.
I've just realised I'd set up my ZX10R shock with standard SRAD shock settings. Funnily enough, that's no good. When will these manufacturers get their act together? After much trial and error I'm now not a million miles away from the actual Kwak settings. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
gsxr shock on pointy settings help needed | widget | SV Talk, Tuning & Tweaking | 5 | 16-05-10 01:12 PM |
Torque settings for gsxr front end | Bunks | SV Talk, Tuning & Tweaking | 3 | 06-10-09 08:06 PM |
GSXR 1000 Settings | pben47 | SV Talk, Tuning & Tweaking | 23 | 28-02-09 08:01 PM |
gsxr 1000 k4 shock settings | tonny006 | SV Talk, Tuning & Tweaking | 4 | 28-09-08 06:47 AM |
front fork settings? | M.C. | SV Talk, Tuning & Tweaking | 1 | 14-07-05 10:16 PM |