SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
|
Thread Tools |
18-05-06, 08:56 PM | #1 |
Guest
Posts: n/a
|
GSXR front end - axle question UPDATED WITH PICS PAGE 2 HELP
Just being doing a trail fit of my GSXR front end before it goes on the bike.
Discovered one disc is bent, another Motoliner trip on the way the axle is the right width for the forks with no wheel in, but with the wheel in place the axle nut and axle do not sit flush each side but stick out about 4mm to get the wheel central. I have a K2 wheel, are there a few types of GSXR axle. Should point out this is on a pointy with GSXR 750 forks. D I need a diffrent axle??? |
18-05-06, 09:11 PM | #2 |
Member
Mega Poster
Join Date: Aug 2003
Location: HomeBound
Posts: 3,302
|
What wheel are you using ?
SRAD wheel(same spoke design as SV) or 'K' series wheel Cheers Ben |
18-05-06, 09:13 PM | #3 |
Guest
Posts: n/a
|
I thought it was a K2 GSXR 600 wheel when i bought it, now I'm wondering if its a older wheel they have sent me...
In that case do I need a SARD axle to sort it, does a SARD wheel have smaller spacing between hub and fork leg? This could be why my axle is sricking out each side? |
18-05-06, 09:17 PM | #4 |
The Sick Man
Mega Poster
Join Date: Nov 2004
Location: Peckham.SE.LDN
Posts: 4,768
|
Have you got the axle in the correct way?
__________________
OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions |
18-05-06, 09:22 PM | #5 | |
Guest
Posts: n/a
|
Quote:
I must need a SARD axle for some reason, the wheel I think must not be a K series! |
|
18-05-06, 09:27 PM | #6 |
The Sick Man
Mega Poster
Join Date: Nov 2004
Location: Peckham.SE.LDN
Posts: 4,768
|
I think i read that this is to do with diffrent axles and years. I beleave that its not a problem as long as the disks are nicley centered in the calipers will give a good indication that the forks are ok. Not 100% but i remember lots of pages re that on SVrider.
__________________
OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions |
18-05-06, 09:40 PM | #7 |
Guest
Posts: n/a
|
take 3.5mm off the nut and al will be fine
|
18-05-06, 09:45 PM | #8 |
Member
Mega Poster
Join Date: Aug 2003
Location: HomeBound
Posts: 3,302
|
Sorry , computer crashed(again)
...so does the wheel look like the SV one? Just so I've got this right. You are usinbg K series forks and K series yokes. That being the case and assumming the wheel is an SRAD one , the axle assumming it's a 'k' series one is fine. All that needs doing is centering of the wheel. With regards to how much of the nut/spacer you should have sticking sticking out , all I can tell you is that it's between 3mm-4mm. I think robw70 made it 3.5mm(I could be wrong). Cheers Ben Edit: I was right then |
18-05-06, 10:08 PM | #9 | |
Guest
Posts: n/a
|
Quote:
K5 GSXR 1000 yokes K3 GSXR 750 legs K3 GSXR axle - I believe K3 GSXR Wheel - I believe, it looks like a K one not a SARD one The type of axle I have should sit flush on both sides and does so with the wheel out. I fI just cut the nut that will place the wheel off center?? |
|
18-05-06, 10:13 PM | #10 |
Guest
Posts: n/a
|
So are the spacers on the SARD axle smaller?
This would solve my problem, am nervous with the idea of holding my wheel centered via the pinch bolts on the fork legs. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GSXR 750 k4 front wheel axle part. | Caddy2000 | Idle Banter | 4 | 22-12-08 10:56 AM |
GSXR front end insurance question | crashers | SV Talk, Tuning & Tweaking | 9 | 07-02-08 06:39 PM |
Project GSXR front end - FITTED WITH PICS PAGE 2 -56K BEWARE | Khewett | SV Talk, Tuning & Tweaking | 32 | 05-06-06 09:25 AM |
Another GSXR front end question - ignnition | Khewett | SV Talk, Tuning & Tweaking | 14 | 19-05-06 07:29 PM |
Ye olde GSXR front end question... | Brand New | SV Talk, Tuning & Tweaking | 5 | 01-07-05 03:40 PM |