SV650.org - SV650 & Gladius 650 Forum



SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000
Need Help: Try Searching before posting

Reply
 
Thread Tools
Old 21-06-05, 12:03 PM   #1
goof
Guest
 
Posts: n/a
Default Can't get an oil reading....

Strange one this, followed from my previous post. With the bike on the side stand I couldn't really get a reading (understandably) - it was lower than the window (I pressume - or just because it was tilted) and I could see that little metal star inside.

I've now got the bike on a paddock stand, where pressumably I can get a correct reading, but now I can't see anything through the window at all...not even the star thingy
Would this indicate there's too much oil in there or what!?

Also, the 18,000 mile service was done on the bike about a year and a half ago but the bike has only done 1000 miles since. Am I best just replacing the oil & filter now? I was going to but the service interval says it's got another 5K before the oil & filter need replacing.
  Reply With Quote
Old 21-06-05, 12:10 PM   #2
philc2000
Guest
 
Posts: n/a
Default

First off, take it off the paddock stand and put it back on it's wheels on a flat surface, get someone to hold the handle bars then have a look. Sometimes paddock stands can tip the bike up too much giving a false reading.

You're supposed to change the oil every year or when you reach the mileage interval - whichever comes sooner - that's what it says in the manual anyway.
  Reply With Quote
Old 21-06-05, 12:10 PM   #3
goof
Guest
 
Posts: n/a
Default

Ah, thanks Phil, change it is then!
  Reply With Quote
Old 21-06-05, 12:11 PM   #4
Carsick
Guest
 
Posts: n/a
Default

You might find that while it's on a paddock stand the forward tilt brings too much oil into view.
You're supposed to check the oil on flat ground with the bike upright.
  Reply With Quote
Old 21-06-05, 12:59 PM   #5
goof
Guest
 
Posts: n/a
Default

Yeah, I used to get an ok reading fir oil with my last bike on the paddock but I guess it didn't have as pitched an engine as the SV.

But unfortunately, just went out to drain it and the god damn draining bolt's rounded

As I'm changing the filter too, will I be able to drain the oil through the filter port?
  Reply With Quote
Old 21-06-05, 01:02 PM   #6
Carsick
Guest
 
Posts: n/a
Default

It won't all drain out through the filter port cos it's not the lowest point.
A few people have had similar problems and I think what they did was try to get a slightly smaller socket over the bolt and then remove it that way. Don't forget to get a replacement and don't blame me if you knacker your engine casing.
  Reply With Quote
Old 21-06-05, 01:17 PM   #7
goof
Guest
 
Posts: n/a
Default

Thanks Carsick - actually, hold on, think I was doing the wrong bolt, pics in the downloaded manual are crap

Assuming I do get it drained, will I need this special tool the manual refers to to remove/install the filter?
The manual says in one sentence "screw it in by hand" and in the next, "do not tighten the filter by hand"

Stick around and pull up a chair, sure I'll have another question in a minute
  Reply With Quote
Old 21-06-05, 01:20 PM   #8
Carsick
Guest
 
Posts: n/a
Default

a filter wrench is handy, but they're not vital, so long as you can get it tight enough by hand.
I think it's 2 full turns once the seal has made contact.
I bought a universal filter wrench cos I can't get mine tight enough by hand and I got fed up of denting the things with a chain wrench.
  Reply With Quote
Old 21-06-05, 01:34 PM   #9
goof
Guest
 
Posts: n/a
Default

Told you, I'm back

Ok, oil is drained \/

However, I can make out bugger all from the manual pics and it just says "remove oil filter"

I know there's the black circular cap I'm guessing I need to get off but as far as I can see there's no bolts around it. Could you guide me through this? Would be much appreciated!
  Reply With Quote
Old 21-06-05, 01:37 PM   #10
Scoobs
Vipers Pillion Bitch
Mega Poster
 
Scoobs's Avatar
 
Join Date: Jul 2003
Location: Waterlooville
Posts: 3,933
Default

The whole filter just spins on. Normal right hand thread. Just unspin it. It may be too tight to undo by hand. You can just stick a screwdriver through it and lever it off with that.
__________________
I look good, I mean really good! Hey everyone come and see how good I look!

Scoobs is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
What Are You Reading? Lissa Idle Banter 178 01-12-08 09:39 AM
Reading festival AndyBrad Idle Banter 11 20-08-08 10:55 PM
I have new reading specs Lozzo Idle Banter 11 30-07-08 01:07 PM
Reading Toy Run trickywoos Guildford Massive 1 05-12-06 02:46 PM
Reading Phoenix South & West Surfers 17 31-03-05 08:30 PM


All times are GMT. The time now is 11:12 PM.


Powered by vBulletin® - Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.