SV650.org - SV650 & Gladius 650 Forum
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   SV Talk, Tuning & Tweaking (http://forums.sv650.org/forumdisplay.php?f=111)
-   -   Stebel Nautilus compact horn anyone? (http://forums.sv650.org/showthread.php?t=162264)

02 Sv650s Black 03-02-11 01:18 PM
Re: Stebel Nautilus compact horn anyone?
 
I got the horn fitted lastnight. Same way as Maviczap. Only thing I have a question about is, what type of tubing should I use to connect the compressor to the horn,

Cbay suggests "Fuel Pipe".

Ended up with a really neat and tidy job.

maviczap 03-02-11 07:14 PM
Re: Stebel Nautilus compact horn anyone?
 
Windscreen washer tube will be fine.

I used medical quality nebuliser tubing I just happened to have lying around :p

yorkie_chris 03-02-11 07:26 PM
Re: Stebel Nautilus compact horn anyone?
 
Quote:
Originally Posted by MattCollins (Post 2473863)
It is much easier to determine which wire does what with a multimeter or test light...

I see little point in the switching... Both horns on mine are always on with a circuit to delay the Stebel by ~500ms so that I can give it a short double tap on the electro-magnetic or hold it for loud and obnoxious. The only time that I would disconnect the stebel by pulling the earth is for roadworthy inspections (air horns are not allowed here).
Fine here though.

Just put relay coil in parallel with or instead of the stock horn, be sure to use a fuse on the hot from the battery.

02 Sv650s Black 03-02-11 09:57 PM
Re: Stebel Nautilus compact horn anyone?
 
Maviczap,

How did you fit the plastic horn piece to the fairing??

Cheers Mark

maviczap 04-02-11 06:22 PM
Re: Stebel Nautilus compact horn anyone?
 
Quote:
Originally Posted by 02 Sv650s Black (Post 2474849)
Maviczap,

How did you fit the plastic horn piece to the fairing??

Cheers Mark
I know I used part of the indicator mount mounting screw for one part

But I can't remember how I attached it to the horn.:smt115

I'll have a look to remind me how I did it :p

02 Sv650s Black 04-02-11 08:17 PM
Re: Stebel Nautilus compact horn anyone?
 
Ive everything connected on the bike, wiring done, compressor fitted under pillion seat, windscreen washer tubing attached to the compressor threaded along the bike to the front and attached to the horn using a valve extender super glued to the horn. The only thing left to do is to secure the plastic horn part in position.

Thanks All for the advice this far.
Mark

Stonesie 04-02-11 09:05 PM
Re: Stebel Nautilus compact horn anyone?
 
Is there much of a delay using a length of tube?

yorkie_chris 04-02-11 09:08 PM
Re: Stebel Nautilus compact horn anyone?
 
none I noticed

02 Sv650s Black 04-02-11 09:19 PM
Re: Stebel Nautilus compact horn anyone?
 
No delay in the air reaching the horn, I thought there might be a delay also, so for a quick test I blew in the end of the washer pipe I was going to use and pointed it at my eye, and you can feel the air right away,
The hose was 2.4metres and I cut approx 700mm of it.

Hope this helps
Mark

Stig 04-02-11 09:25 PM
Re: Stebel Nautilus compact horn anyone?
 
Quote:
Originally Posted by 02 Sv650s Black (Post 2474045)
This means the connection between the horn and relay would be 3ft or so. Depending where the horn was fitted.
3ft? Seriously?

Quote:
Originally Posted by 02 Sv650s Black (Post 2475528)
No delay in the air reaching the horn, I thought there might be a delay also, so for a quick test I blew in the end of the washer pipe I was going to use and pointed it at my eye, and you can feel the air right away,
The hose was 2.4metres and I cut approx 700mm of it.

Hope this helps
Mark
I'm not sure I would have used my eye as the test target. :)


All times are GMT. The time now is 01:56 PM.
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.