SV650.org - SV650 & Gladius 650 Forum

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)

- SV Talk, Tuning & Tweaking (http://forums.sv650.org/forumdisplay.php?f=111)

- - Suzy got nekkid!! (http://forums.sv650.org/showthread.php?t=103356)

Re: Suzy got nekkid!!

Quote:

Originally Posted by pmapp (Post 1397259)

mmmmmmm, buns.

Time should I turn up? :-D

haha the word 'bun' really doess make everyones ears ***** up eh?? if ya know where eee lives ya can have a bun......if theres any left after Smudge gets his hands on em...he'll be over later to have a laugh at my rusty nuts..lol

Quote:

Originally Posted by Lozzo (Post 1397332)

If they're studs with nuts I'd just split the nuts, or Dremel them off, then run a die down the threads and put them back the way they were with a good dollop of high temp copper grease on the threads and brass nuts. I did this to my mates early Hinckley Triumph a while back and they were fine when the exhaust needed to come off a few years later.

If you've got the cheese cap-head bolts that Suzuki fit as standard, or hex head ones, then you're in for fun and games involving heat and Plus-gas, with a possible appearance from drills and taps.

Get them out and stick some exhaust studs in with brass nuts.

they are the original cheeeesy studs and nuts...well whats left of the nuts that is... i wish i'd taken a photo of the half disintegrated ones that crumbled off when you poked em. The studs however seem to be an absolute mother to tackle

Re: Suzy got nekkid!!

They're M6 studs with nuts on. I have some stainless replacements, however I can hardly get a spanner on these at all.

Freeze and release spray, propane, and if it really annoys me, oxyacet is ready.

I have spare heads if it comes to that, but they're from a 99, so black coated which I don't think she'd like!

Going to throw a load of fairing panels at her in a minute or 3 as they're in my way, and she's gone to the butty shop good girl that she is.

Re: Suzy got nekkid!!

argggghhhh no buns at the butty shop!!!!!!!! you'll all have to bring your own!!
The guy in the hardware shops a biker, i've just been to ask him for an angle grinder wheel. He laughed and said 'shes really that bad he's got to take such drastic measures?????!!!!

I flippin hope not

Re: Suzy got nekkid!!

I've got some rather gruesome photo's of Suzy now which I shall be uploading soon. Maybe a guide to how not to treat your SV!!. i have now been polishing the forks for 2 days!!:smt010. They are rather pitted, look better than what they were ,but, i am now going to have to get nasty, as my elbows have run out of grease and my poor little fingies are worn to the bone. The nitromorse trick of Lissa'a kinda worked, but these mothers are sooo bad.

Chris still hasn't managed to get the studs even loose, the nuts had to be cut off.

Re: Suzy got nekkid!!

Right.

The nuts came off when I ground half of them off, could then spin them off by tapping them with a punch.

Had to get a fine chisel behind the clamping plate to get that to shift.

Just got the actual header out of the head as it was rusted solid. Had to soak it in penetrant oil for 2 days, use freeze and release on it, then beast it with a lump of wood and a hammer.

The studs are currently having a bath, will have a go at those tomorrow, say a prayer for them! :-P

Re: Suzy got nekkid!!

Quote:

Originally Posted by yorkie_chris (Post 1398551)

say a prayer for them! :-P

[-o<[-o<[-o<[-o<[-o<[-o<

(think that should do it :))

Re: Suzy got nekkid!!

PLEASE ORG PRAY FOR SUZE

:grouphug:she also needs one of these too

Re: Suzy got nekkid!!

warning the following photos show graphic images of RUST!!!!!!

Re: Suzy got nekkid!!