SV650.org - SV650 & Gladius 650 Forum

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   SV Talk, Tuning & Tweaking (http://forums.sv650.org/forumdisplay.php?f=111)
-   -   Valve clearances = New Gasket? (http://forums.sv650.org/showthread.php?t=150365)

SAMMY650 21-04-10 06:39 PM

Valve clearances = New Gasket?
 
Just a quick question.....I'm about to check the valve clearances on my k6 sv650s, will i need to replace the cylinder head gasket or can i just use the old one is its not damaged???

thanks

SAMMY650 21-04-10 07:02 PM

Re: Valve clearances = New Gasket?
 
Also, will i have to remove the radiator or can the clearances be checked without removing the rad?

BBadger 21-04-10 07:04 PM

Re: Valve clearances = New Gasket?
 
Rad must come off to get to the front im afraid.
But no, no gaskets involved just the cyclender head cover i believe.
Some one with more knowledge will be along soon though.

maviczap 21-04-10 07:05 PM

Re: Valve clearances = New Gasket?
 
Rocker cover gasket is silcon rubber, so won't need replacing

BBadger 21-04-10 07:13 PM

Re: Valve clearances = New Gasket?
 
Nope....actually was at spannermans today while he was doing this.

Take off and clean all surfaces well and then i believe you re-grease slap back on and tighten everything back up.

[Edit]
Again dont take my word on the putting back together bit may need somthing else than rubber grease =s

NedSVS 21-04-10 07:14 PM

Re: Valve clearances = New Gasket?
 
The cam cover has a rubber gasket which you can re-use so long as you don't damage it, I bought new (not cheap) but could have saved my money. Old or new, apply a little sealant where the half round sections fit in the head. I did not remove the rad completely, I may have tilted it forward; some time ago now and I don't have the best memory, but I think I removed the airbox and got some access from above. Hope this helps.

SAMMY650 21-04-10 07:14 PM

Re: Valve clearances = New Gasket?
 
Cheers for the info guys:thumbsup:

BBadger 21-04-10 07:16 PM

Re: Valve clearances = New Gasket?
 
Quote:

Originally Posted by NedSVS (Post 2248265)
I did not remove the rad completely, I may have tilted it forward

TBH taking it off and replacing the coolant unless you did it recently cant hurt though and makes things less fidderly.

Spanner Man 22-04-10 05:57 AM

Re: Valve clearances = New Gasket?
 
Quote:

Originally Posted by BBadger (Post 2248264)
Nope....actually was at spannermans today while he was doing this.

Take off and clean all surfaces well and then i believe you re-grease slap back on and tighten everything back up.

[Edit]
Again dont take my word on the putting back together bit may need somthing else than rubber grease =s


Not grease young fella. A little silicone sealant around the cut outs. (These are the half moon shaped things).
Make sure you clean all the old sealant from the cylinder head, & the gasket itself before replacing the cover, or it'll probably leak.
If the gasket comes away from the cylinder head cover, hold it in place with a few drops of Superglue on the outside edge only.


Cheers.

BBadger 22-04-10 08:32 AM

Re: Valve clearances = New Gasket?
 
What he said ^^


All times are GMT. The time now is 03:43 PM.

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.