SV650.org - SV650 & Gladius 650 Forum
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   SV Talk, Tuning & Tweaking (http://forums.sv650.org/forumdisplay.php?f=111)
-   -   R&G bungs for K3 ...problems (http://forums.sv650.org/showthread.php?t=93614)

scarlett 18-07-07 04:37 PM
R&G bungs for K3 ...problems
 
I recently bought (or should I say...got ripped off) on a pair of r&g's for my K3 2004 naked.

Well they have arrived today, without a fitting kit. Basically all I have got is the engine bar and black nylon bungs....looks like a lightweight dumbell.

So I am guessing there are bits missing. e.g. aluminium block., nuts, washers etc.

Can anyone help me out.....could do with a list of what I actually need to fit the damn things....or can I fit them without all the bits?

Thanks in advance.

kwak zzr 18-07-07 04:47 PM
Re: R&G bungs for K3 ...problems
 
my R&G's are the same bar you are talking about but they have 2 alloy threaded cups each end for the nylon sliders to screw into.

SoulKiss 18-07-07 04:49 PM
Re: R&G bungs for K3 ...problems
 
Look R&G up on the web and call them.

They will tell you what you should havem ans allow you to buy what you need and get the bits to you next day (usually)

David

kwak zzr 18-07-07 04:52 PM
Re: R&G bungs for K3 ...problems
 
i phoned them for a new bar and nut set they posted next day @ £18 but when i took the old one out it was only the nuts that had threaded:( should have cost about 50p

scarlett 18-07-07 05:03 PM
Re: R&G bungs for K3 ...problems
 
1 Attachment(s)
On the r&g website its says they should be sited like this....... please attachment.
but when I look at pics of other sv's they are not done like the pic (the r&g pic shows a aluminium block)...
What do you reckon??

Biker_Billy 18-07-07 06:55 PM
Re: R&G bungs for K3 ...problems
 
Quote:
Originally Posted by scarlett (Post 1241335)
On the r&g website its says they should be sited like this....... please attachment.
but when I look at pics of other sv's they are not done like the pic (the r&g pic shows a aluminium block)...
What do you reckon??
I fitted some R & G's to my K3 (faired) last week, and they came with the aluminium blocks. I presume the unfaired is the same as they mount to the same points on the frame...

I'd call them, to me it seems you are missing vital parts.

scarlett 18-07-07 07:20 PM
Re: R&G bungs for K3 ...problems
 
Quote:
Originally Posted by Biker_Billy (Post 1241395)
I fitted some R & G's to my K3 (faired) last week, and they came with the aluminium blocks. I presume the unfaired is the same as they mount to the same points on the frame...
When I look at photos of other peoples K3's in the gallery section, they dont seem to have to aluminium blocks....thats whats throwing me.

kwak zzr 18-07-07 08:09 PM
Re: R&G bungs for K3 ...problems
 
you are looking at the new design R&G's which do fit like that, mine are the old type where you have a threaded bar about 14 inches long which goes straight through the middle of the engine with a nylon bung on each end.

scarlett 18-07-07 08:41 PM
Re: R&G bungs for K3 ...problems
 
Quote:
Originally Posted by kwak zzr (Post 1241457)
you are looking at the new design R&G's which do fit like that, mine are the old type where you have a threaded bar about 14 inches long which goes straight through the middle of the engine with a nylon bung on each end.
Ah ok, I get it now...the secondhands ones I have bought, are the old ones...good, so they will fit then. Thanks.

kwak zzr 18-07-07 08:44 PM
Re: R&G bungs for K3 ...problems
 
have you got the 2 alloy threaded cups for either side?


All times are GMT. The time now is 09:05 AM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.