SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
I did the wirral egg run yesterday which was absolutley brill except for a gear problem, basically I could get it in to first gear but it then wouldnt release in to second or vice versa, it meant spending a good part of the 90 min run holding the clutch in cos it wouldnt go into neutral either, once running though and a bit of speed built up it was fine, any ideas whats causing it on me 2001 curvey ? is it normal or is the gear selector shagged ? I topped the oil up recently and might have used a 15/40 instead of a 10/40 could that be a reason ?
Thanks guys |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
![]()
Is your chain tight enough (ie, not too slack)?
What about the clutch? Does it need tightening? Mine bites when the lever is quite far out, so selecting neutral when stopped is easier. If you think they're okay, you might find that rolling yourself forward a few inches and trying again will work. |
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
![]()
Thanks JG, everything seems ok tbh, I was wondering if the extra heat build up cos of sitting in basically a huge traffic jam for the first couple of miles of the egg run could have caused it, once out of the towns it was ok again.
|
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
![]()
I found with my SV the oil level was crucial to being able to find neutral, if it was higher or lower than middle full (in the window) or the chain was a little too tight or loose, i couldnt find neutral without turning the engine off.
HTH Marshall |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]()
Hi Stewie, was gonna suggest checking that the lever isn't binding and might need an oil, but I reckon it could have been the heat causing the clutch plates to swell.
|
![]() |
![]() |
#6 |
Guest
Posts: n/a
|
![]()
Stew, on that, I used to have to spray a bit of WD40 on the pivot on the selector and that seemed to clear it up after a while. Used to get it a bit myself on that one. Try the WD40 trick first and take her out for a spin.
|
![]() |
![]() |
#7 |
Da Cake Boss
Mega Poster
Join Date: May 2007
Location: On a flying Horse
Posts: 9,992
|
![]()
theres a little plastic cover, on the left hand side, in front of the frame..pretty sure the front sprocket is behind it. Got the clutch cable attached to it. Damn sure if you stick your head under your bike you'll see a massive lump of oily crud stuck behind that.
Last time this happened to me I sat with a pointy stick and poked the whole lot out. It cured my problem.....try it you never know!!
__________________
Suzy, yellow 2001 SVS. Kitty, V-Raptor 1000, ZZR1400<<its my bike now Pegasus! Hovis 13.8.75-3.10.09 Reeder 20.7.88-21.3.12 |
![]() |
![]() |
![]() |
#8 |
Guest
Posts: n/a
|
![]() |
![]() |
![]() |
#9 |
Da Cake Boss
Mega Poster
Join Date: May 2007
Location: On a flying Horse
Posts: 9,992
|
![]() ![]()
__________________
Suzy, yellow 2001 SVS. Kitty, V-Raptor 1000, ZZR1400<<its my bike now Pegasus! Hovis 13.8.75-3.10.09 Reeder 20.7.88-21.3.12 |
![]() |
![]() |
![]() |
#10 |
Guest
Posts: n/a
|
![]()
Right thanks everyone Ill have a look this afters
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Longer gear selector rod? | DarrenSV650S | Bikes - Talk & Issues | 2 | 15-03-09 08:24 PM |
gear selector rod thing | husky03 | Stuff Wanted | 7 | 31-01-08 07:02 PM |
Gear Selector Foot Peg | T0mm0 | SV Talk, Tuning & Tweaking | 17 | 10-08-05 02:38 PM |
Gear selector for my Sk1 | sexysi | SELKENT | 4 | 22-04-05 03:42 PM |
Help! Where can I get gear selector lever? Thanks. | jump | SV Talk, Tuning & Tweaking | 5 | 14-03-05 12:17 PM |