Pyramid Plastics - SV650.org

11-12-05, 05:19 PM

hello guys and gals - writing from the states - I was looking for any comments on Pyramid Plastics - specifically belly pans - I have an 02 naked model and was curious as to quality and ease of fitment for their kits?? Thanks in advance!

Best Regards

11-12-05, 09:05 PM

yeah hi,

they very good in my experince, well made & easy to fit.

11-12-05, 09:09 PM

Thanks for your response!

11-12-05, 11:40 PM

I have one on my half faired K4 , well made, easy to fit (if you can use lego u can put this on your bike) and most importantly it does its job (LOOKING S**T HOT)

northwind · 12-12-05, 12:35 AM

I love the Pyramids bellypan for the carbed model, it just looks right... The fit is absolutely spot on too, they're a bit of a fiddle to fit but then so are most bellypans. Very solid too.

They hang a little low as standard, I managed to ground mine out on the left hand side a couple of times

but you do have to be trying quite hard to do that. Also, because the exhaust header is quite tight through the cutout in the front, aftermarket exhausts can be a problem- as I found out. Lots of fillering and cutting required to make it fit with my system. Well worth it though.

12-12-05, 04:48 PM

northwind - what type exhaust do you have? I've got a full Micron - hopefully I won't have any problems though??

northwind · 12-12-05, 05:31 PM

Mine is a WRP, it runs the front header down the side of the oil filter for some unknown reason... Looks good though

Not sure about Micron. Does it go more or less where the stock one does- ie down the front of the filter?

12-12-05, 06:13 PM

Yes.....The Micron header runs the same pattern as the stock system. Straight out the front of the oil filter.

12-12-05, 06:31 PM

i got a pyramid belly pan on my pointy which looks graet but wont catch any oil should it need to. (which is its main function isnt it?)

12-12-05, 06:35 PM

Yes - it really serves no function except for looks and perhaps protecting the bottom pattern of the header.

11-12-05, 05:19 PM	#1
Jacques Guest Posts: n/a	Pyramid Plastics hello guys and gals - writing from the states - I was looking for any comments on Pyramid Plastics - specifically belly pans - I have an 02 naked model and was curious as to quality and ease of fitment for their kits?? Thanks in advance! Best Regards

12-12-05, 12:35 AM	#5
northwind Moderator Mega Poster Join Date: Jan 2004 Location: In the garage where I belong Posts: 17,083	I love the Pyramids bellypan for the carbed model, it just looks right... The fit is absolutely spot on too, they're a bit of a fiddle to fit but then so are most bellypans. Very solid too. They hang a little low as standard, I managed to ground mine out on the left hand side a couple of times but you do have to be trying quite hard to do that. Also, because the exhaust header is quite tight through the cutout in the front, aftermarket exhausts can be a problem- as I found out. Lots of fillering and cutting required to make it fit with my system. Well worth it though. __________________ "We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed"

12-12-05, 05:31 PM	#7
northwind Moderator Mega Poster Join Date: Jan 2004 Location: In the garage where I belong Posts: 17,083	Mine is a WRP, it runs the front header down the side of the oil filter for some unknown reason... Looks good though Not sure about Micron. Does it go more or less where the stock one does- ie down the front of the filter? __________________ "We are the angry mob, we read the papers every day We like what we like, we hate what we hate But we're oh so easily swayed"

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Tank Protector, Pyramid Plastics	toonyank	For Sale - SV's and SV related items	6	05-12-08 04:27 PM
pyramid plastics hugger	maff	Photos	28	15-11-08 04:42 PM
Pyramid plastics headlight cover	danf1234	SV Talk, Tuning & Tweaking	2	10-05-07 06:01 PM
Good service from Pyramid Plastics	Grinch	SV Talk, Tuning & Tweaking	5	11-03-05 09:43 AM

11-12-05, 09:05 PM	#2
hall13uk Guest Posts: n/a	yeah hi, they very good in my experince, well made & easy to fit.

11-12-05, 09:09 PM	#3
Jacques Guest Posts: n/a	Thanks for your response!

11-12-05, 11:40 PM	#4
leejbarker Guest Posts: n/a	I have one on my half faired K4 , well made, easy to fit (if you can use lego u can put this on your bike) and most importantly it does its job (LOOKING S**T HOT)

12-12-05, 04:48 PM	#6
Jacques Guest Posts: n/a	northwind - what type exhaust do you have? I've got a full Micron - hopefully I won't have any problems though??

12-12-05, 06:13 PM	#8
Jacques Guest Posts: n/a	Yes.....The Micron header runs the same pattern as the stock system. Straight out the front of the oil filter.

12-12-05, 06:31 PM	#9
bobbydazzler Guest Posts: n/a	i got a pyramid belly pan on my pointy which looks graet but wont catch any oil should it need to. (which is its main function isnt it?)

12-12-05, 06:35 PM	#10
Jacques Guest Posts: n/a	Yes - it really serves no function except for looks and perhaps protecting the bottom pattern of the header.