 |
 |
21-03-17, 08:55 PM
|
#1011 |
|
Member
Mega Poster
Join Date: Dec 2007
Posts: 2,708
|
Re: What have you tinkered with today?
Basically a 6mm triangular plate behind the footrest hanger and secured with the same two bolts, hole drilled and tapped to take the shift lever pivot shaft with lock nut behind. The horn on the shift shaft is actually two that I welded together (with one of the horns cut off) as I need to bring it out far enough to clear the side stand and spring. There were a couple of other small things that had to be done, I added some weld to the side stand so that it came up 10mm less and didn't hit my new lever and I had to make spacers for the lower two fairing bolts to move it out and prevent it from fouling the linkage.
|
|
|
|
21-03-17, 09:32 PM
|
#1012 |
|
John T
Mega Poster
Join Date: May 2003
Location: Shrewsbury, Shrops, UK
Posts: 2,492
|
Re: What have you tinkered with today?
Brill. Thanks
__________________
Admin for this forum and the main site. John@sv650.org |
|
|
|
|
24-03-17, 11:14 AM
|
#1013 |
|
Member
Mega Poster
Join Date: Jul 2003
Location: In the shadows to the left
Posts: 7,700
|
Re: What have you tinkered with today?
Trying to upgrade 103 Xerox Colorqube printers to the latest firmware, using all but the most painful method (Visiting every device with a USB stick, 70 locations throughout south london) and failing
|
|
|
|
|
24-03-17, 12:52 PM
|
#1014 | |
|
Member
Join Date: Feb 2015
Location: Rainham, Essex
Posts: 143
|
Re: What have you tinkered with today?
Quote:
|
|
|
|
|
|
24-03-17, 01:09 PM
|
#1015 |
|
John T
Mega Poster
Join Date: May 2003
Location: Shrewsbury, Shrops, UK
Posts: 2,492
|
Re: What have you tinkered with today?
Woodwork today. Adding a ramp to our dining room so my wife can get in and out with her wheelchair.
__________________
Admin for this forum and the main site. John@sv650.org Last edited by admin; 25-03-17 at 08:03 AM. |
|
|
|
|
30-03-17, 04:32 PM
|
#1016 |
|
Member
Join Date: May 2016
Location: St Albans
Posts: 364
|
Re: What have you tinkered with today?
Front callipers serviced and new front brake lines installed. One piston on each calliper stiff, and rust between the dust and oil seals, so definitely needed doing. I just need to go for a ride to test them out now ...
|
|
|
|
|
31-03-17, 08:47 AM
|
#1017 |
|
Guest
Posts: n/a
|
Re: What have you tinkered with today?
New collector box finally on the VF1000FF and it's in for MOT.
|
|
|
|
14-06-17, 07:12 PM
|
#1018 |
|
John T
Mega Poster
Join Date: May 2003
Location: Shrewsbury, Shrops, UK
Posts: 2,492
|
Re: What have you tinkered with today?
Rear cam chain tensioner clattering on the VFR. Time to pop it off and give it a service.
__________________
Admin for this forum and the main site. John@sv650.org |
|
|
|
|
17-06-17, 03:23 PM
|
#1019 |
|
Member
Join Date: Jan 2014
Location: North Yorkshire
Posts: 284
|
Re: What have you tinkered with today?
After having a stone make quite an impression on my radiator, I decided prevention was better than cure.
The covers that Admin is selling fit an 04 pointy no problem and look very nice too. http://forums.sv650.org/showthread.php?t=225731 Last edited by yokohama; 17-06-17 at 03:25 PM. |
|
|
|
|
17-06-17, 09:31 PM
|
#1020 |
|
John T
Mega Poster
Join Date: May 2003
Location: Shrewsbury, Shrops, UK
Posts: 2,492
|
Re: What have you tinkered with today?
Glad it fitted okay. The s/steel is good quality and will keep it's shine.
__________________
Admin for this forum and the main site. John@sv650.org |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Been got already today.. | 454697819 | Idle Banter | 16 | 01-04-10 02:08 PM |
| Today | DaveP | The Border Patrol | 4 | 02-03-10 10:52 AM |
| Going out today? | tj2 | The Border Patrol | 1 | 01-06-09 09:22 PM |
| Today | Tara | Guildford Massive | 14 | 02-06-08 11:56 AM |
| Today...... | Caddy2000 | Idle Banter | 15 | 19-04-06 05:39 PM |
