SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#11 |
Junior Member
Join Date: Dec 2016
Posts: 10
|
![]()
Sorry to revive this old thread but im a bit stuck. I have a 02 curvy, Im trying to replace the complete linkage assembly and a replacement rear shock while im at it.
I really, really dont want to meddle with the exhaust header nuts at all, so my question is how do i do this with exhaust in place? I have managed to undo the nut that attatches the dogbone to swingarm with a socket and breaker but these nuts are sooo tight. Ive tried the others from the left (bolt side) but I know I need to be tackling the nut side really but there is no room there for a socket with the exhaust on. I can see on the pics above the exhaust is in place but has anyone any info on how i do it. Thanks in advance, Steve Last edited by stevieo; 13-07-22 at 10:55 PM. |
![]() |
![]() |
![]() |
#12 |
Member
Mega Poster
Join Date: Mar 2010
Location: Mid Wales
Posts: 2,547
|
![]()
Steve, I am struggling to remember the details of this job. The exhaust definitely stayed in place, but I can't remember what spanner I used. I have a vague idea I managed to work a ring spanner in there to go on the nut, possibly with a tube over the spanner as an extension.
I'd advise giving the nut/bolt thread a good dowsing in PlusGas and leaving it to soak in first though. |
![]() |
![]() |
![]() |
#13 |
Junior Member
Join Date: Dec 2016
Posts: 10
|
![]()
Thankyou - looking at it there is room for a ring spanner with the wheel off. I didnt think about putting a bar on the spanner though. I have all the nuts and bolts on the new linkage so am ok if i damage anything in the process. Im putting the bike on the stands next week, I was just testing last night to see if I could crack them first. Cheers
|
![]() |
![]() |
![]() |
#14 |
Member
Mega Poster
Join Date: Mar 2010
Location: Mid Wales
Posts: 2,547
|
![]()
Don't forget you can't use a rear paddock stand for the job! It's why I hung my SV off the stepladder.
|
![]() |
![]() |
![]() |
#15 |
Junior Member
Join Date: Dec 2016
Posts: 10
|
![]()
Yes, I will be using 2 axle stands, I have also ordered a long reach 17mm ring spanner, 430mm long so should be a big help.
|
![]() |
![]() |
![]() |
#16 |
Member
Mega Poster
Join Date: Mar 2010
Location: Mid Wales
Posts: 2,547
|
![]()
How did you get on with this job Steve?
|
![]() |
![]() |
![]() |
#17 |
Junior Member
Join Date: Dec 2016
Posts: 10
|
![]()
So sorry I didnt post results, havent been back on here since then, but for anyone else digging this up in the future .....
Yes, all was fine Gary, 2 axle stands under the footpegs (reverse the footpegs first), 17mm long reach flat ring spanner, not the angled type and a bar and yes, it can be done with the exhaust in place. I have pics if anyone needs them. Linkage bearing were powder btw so needed doing ![]() |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
K3> linear rear linkage. | lawson17 | For Sale - SV's and SV related items | 0 | 01-05-15 06:07 PM |
Rear suspension linkage wanted | theboatman | Stuff Wanted | 12 | 21-05-13 10:02 PM |
Rear linkage bearings | yorkie_chris | SV Talk, Tuning & Tweaking | 5 | 16-02-10 11:14 PM |
rear suspension linkage spreadsheet | erik | SV Talk, Tuning & Tweaking | 1 | 22-02-09 09:03 AM |
Cleaning all around the rear wheel / swingarm / rear brake caliper | Camel | SV Talk, Tuning & Tweaking | 12 | 28-04-08 02:00 PM |