USD GSXR1000 k1 forks | standed forks - curvy

[yorkie_chris]

Originally Posted by Bibio

Speedo sensor, Cherry switch GS100701, home made bracket
Cost £29.27 RS Components

Originally Posted by Nicky S

were all you have done is told me ant ya i ment a link to a site or something

http://lmgtfy.com/?q=rs+components

[Nicky S]

Originally Posted by yorkie_chris

http://lmgtfy.com/?q=rs+components

dont undertsnad this bit ... Sensor; 15-32 in.-32; Sink; 4.5 to 24 VDC; 6 mA (Max.); 400 mV (Max.); 1 in.

will i need magnets as well or do they come with the sensor ?

http://uk.rs-online.com/web/search/s...00701&x=2&y=19

[yorkie_chris]

That is spec of sensor.

You need magnets also.

Bibios choice is OK but I found it better to use some countersunk magnets off eBay, that way they can simply be bolted through the disc rivets with some M4 bolts and nylocs. Totally secure and swappable between discs.

[Nicky S]

Originally Posted by yorkie_chris

That is spec of sensor.

You need magnets also.

Bibios choice is OK but I found it better to use some countersunk magnets off eBay, that way they can simply be bolted through the disc rivets with some M4 bolts and nylocs. Totally secure and swappable between discs.

have you got a picture of this ???

write so after are long thread which is full of info is my list below right ?

GSXR1000 K1 Bits

* USD Forks
* Callipers + Bolts
* Mud Guard

SRAD Bits

* Top Yoke
* Top Yoke Nut (51353-27C40)
* Top Yoke Washer (51356-29E00)
* Adjuster Nut x2 (51631-33E00)
* Adjuster Washer To Suit x1 (51631-33E00)
* Bottom Yoke
* Spindle
* Wheel
* Discs

Other bits needed

* TWF Bearing (Clicky For Link)
* Parts To Make Speedo (Clicky For Link) + Magnets

[yorkie_chris]

OK

move the discs to the SRAD bits section (the 0.5mm offset we were jabbering about earlier!) (bolts it doesn't matter, they are same)

Add; SRAD adjuster nuts x2 and adjuster washer. (Will find you some suzuki part numbers in a bit)

[Nicky S]

Originally Posted by yorkie_chris

OK

move the discs to the SRAD bits section (the 0.5mm offset we were jabbering about earlier!) (bolts it doesn't matter, they are same)

Add; SRAD adjuster nuts x2 and adjuster washer. (Will find you some suzuki part numbers in a bit)

cheers YC

my list ok yer ....

quick question which i didnt think about what about the speedo and headlight ?

also am i being stupid but arnt these the same part ?

* Top Yoke Nut And Washer
* Adjuster Nuts x2 And Adjuster Washer

[yorkie_chris]

No they are not.

The top yoke nut goes above the top yoke.
The adjuster nuts go below the top yoke with the adjusters washer between them... for the purpose of adjusting the head bearings.


Of course if these were not there, and you simply tightened the top yoke nut and clamped the bearings rigidly with the full torque of assembly. The bearings would be preloaded so much that damage would be inevitable.

[Nicky S]

Originally Posted by yorkie_chris

No they are not.

The top yoke nut goes above the top yoke.
The adjuster nuts go below the top yoke with the adjusters washer between them... for the purpose of adjusting the head bearings.


Of course if these were not there, and you simply tightened the top yoke nut and clamped the bearings rigidly with the full torque of assembly. The bearings would be preloaded so much that damage would be inevitable.

ahhhhhhhh i see YC your a clever guy

you got any pictures of your front end ??

also how will i get over the problem of mounting the gauges and headlight ?

[yorkie_chris]

Headlight, you can get some universal headlight clamps, they're fairly common for streetfightery type bikes.

Clocks, I filled the back of the top yoke with fibreglass and drilled and tapped that. Bodgetastic, but it worked temporarily.... and is still there now!

[Nicky S]

Originally Posted by yorkie_chris

Headlight, you can get some universal headlight clamps, they're fairly common for streetfightery type bikes.

Clocks, I filled the back of the top yoke with fibreglass and drilled and tapped that. Bodgetastic, but it worked temporarily.... and is still there now!

bodge dosent sound lik a YC job lol
ill have to have more of a look at it when i have all the bits i need and start doing it.

can i see a picture if you have one of the magnets for the speedo ?

any part numbers for them bits ?