SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Member
Mega Poster
Join Date: Apr 2010
Location: Newcastle upon Tyne, Just south of salad dodging country
Posts: 7,750
|
![]()
Evening all
I'm just wanting to double check the size of the exhaust studs on the Curvies. Went to replace the nuts to find the bugger was undoing the stud on both sides, grrr. Any help is appreciated. Also; is copperslip ok as an anti-sieze in the block?
__________________
RIP Reeder 20/07/1988 - 21/03/2012. Always missed squire!!! Every year we meet old friends, gain some new ones, lose old ones and you always remember them all. “Live as if you were to die tomorrow. Learn as if you were to live forever.” Mahatma Gandhi |
![]() |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
![]()
think they are m8's like on the pointy also coper slip is fine ps you can mix it with thread lock so they stick in as well but dont corrode in
|
![]() |
![]() |
#3 |
Member
Mega Poster
Join Date: Apr 2010
Location: Newcastle upon Tyne, Just south of salad dodging country
Posts: 7,750
|
![]()
cheers Dan
Had a feeling it was M8, but I don't trust pro bolts website with a few things
__________________
RIP Reeder 20/07/1988 - 21/03/2012. Always missed squire!!! Every year we meet old friends, gain some new ones, lose old ones and you always remember them all. “Live as if you were to die tomorrow. Learn as if you were to live forever.” Mahatma Gandhi |
![]() |
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
![]()
no problem
ohh they are m8x 1.25pitch i used 45mm long studs with 2 brass bolts one tightened against the manifold and then the other against the other nut |
![]() |
![]() |
#5 |
Member
Mega Poster
Join Date: Apr 2010
Location: Newcastle upon Tyne, Just south of salad dodging country
Posts: 7,750
|
![]()
ideal!
Going to do the dealer ring round on monday, see if I hit lucky with someone with SS ones in stock
__________________
RIP Reeder 20/07/1988 - 21/03/2012. Always missed squire!!! Every year we meet old friends, gain some new ones, lose old ones and you always remember them all. “Live as if you were to die tomorrow. Learn as if you were to live forever.” Mahatma Gandhi |
![]() |
![]() |
![]() |
#6 |
Guest
Posts: n/a
|
![]()
do! i said two bras bolts i meant nuts
![]() |
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]()
Yes copper slip is fine to use also silver paste.
And if the studs are undoing aswell put the stud in a vice then undo the nut from there . then put it back on and tighten it up . if the stud does not tighten it up properly then use two nuts do them up it will screw the stud back in . hope that helps Ollie |
![]() |
![]() |
#8 |
Guest
Posts: n/a
|
![]()
the bolts that hold the pillion handle work well too
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Broken exhaust stud. | barwel1992 | SV Talk, Tuning & Tweaking | 17 | 10-01-11 09:12 AM |
99 (curvy) Exhaust Stud Things | vardypeeps | SV Talk, Tuning & Tweaking | 9 | 31-10-08 08:59 PM |
Snapped Exhaust stud! | spacehog | SV Talk, Tuning & Tweaking | 4 | 22-05-08 08:21 PM |
Whats the ehaust stud size for a pointy? | DanF | SV Talk, Tuning & Tweaking | 3 | 15-05-07 12:39 PM |
exhaust stud | dirtydog | SV Talk, Tuning & Tweaking | 13 | 14-02-06 04:07 PM |