Log in

View Full Version : Stubbie'd my endcan.

Pages : 1 [2]
aarond
22-01-08, 10:56 PM
will probably do it at weekend, unsure how it will look not being a high level

mine isn't a high level either so will put a pic up when done which should hopefully be tomorrow as i need to get some 4mm rivets tomorrow.
Wideboy
22-01-08, 11:00 PM
mine isn't a high level either so will put a pic up when done which should hopefully be tomorrow as i need to get some 4mm rivets tomorrow.


ok cheers mate look forward to it
Richie
23-01-08, 12:12 AM
yeah but mine is the one where you have that big plate of spagetti and the string going from mouth to mouth :smt046
amazing what photoshop can do :smt114

you sir are a very very bad man.

:smt077;)
aarond
23-01-08, 06:07 PM
ok cheers mate look forward to it

job done looks good an sounds good(in my opinion!!;))

http://i166.photobucket.com/albums/u95/ad53ggz/IMG_0449.jpg
http://i166.photobucket.com/albums/u95/ad53ggz/IMG_0448.jpg
http://i166.photobucket.com/albums/u95/ad53ggz/IMG_0447.jpg
Wideboy
23-01-08, 06:13 PM
that looks ace! thought it would look rubbish with out being a high level

how long did you make it?, shame about where the strap is:(

might do mine at the week end :smt077
aarond
23-01-08, 06:21 PM
i took about 7.5inches off i did it like yorkie chris by taking off the bottom cap and cutting out a section on the bottom but if i was doing it again i think i would take off the top cap and cut the top because the center cylinder bit of the exhaust was a b**ch to get back into the top end cap maybe worth taking a note how far the center cylinder tube goes into the end cap.hope this makes sense
aarond
23-01-08, 06:22 PM
N.B. forgot to say DO IT:smt077
Wideboy
23-01-08, 06:24 PM
why was the tube hard to get back into the top cap? and how did you eventually do it?
aarond
23-01-08, 06:39 PM
well it was just hard to get it lined up right, patience was the main thing then start hitting/taping then end cap in. Like those before i had to cut notches in the end cap and bend them over a bit to aid getting the end cap into the exhaust. N.b. also hard cos it is a tight fit in the first place!
Richie
23-01-08, 06:41 PM
\\:D/Looks cool mate, bet it sounds the mutts danglies too.
aarond
23-01-08, 06:50 PM
\\:D/Looks cool mate, bet it sounds the mutts danglies too.
I think so!!!:D
ljharmitt
16-02-08, 12:40 AM
which end did you cut off? From the downpipes or from the end?
ljharmitt
16-02-08, 12:44 AM
Just gone and had a look at mine.. here's a couple of pics. To me (and I don't know a thing ;)) it looks like a bit too much work to cut this down, or is it doable?

It screws in from the end, not on the sides of the can itself.

http://img32.picoodle.com/img/img32/4/1/20/f_Image040m_e014ab5.jpg




http://img37.picoodle.com/img/img37/4/1/20/f_Image042m_a4aec83.jpg

What say you? :rolleyes:

Oh btw my exhaust is like this also, any more info on how id do it?