SV650.org - SV650 & Gladius 650 Forum

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   Bikes - Talk & Issues (http://forums.sv650.org/forumdisplay.php?f=129)
-   -   Coolant removal - how? (http://forums.sv650.org/showthread.php?t=197865)

granty92 26-04-13 08:24 AM

Coolant removal - how?
 
Hi guys and gals
So yesterday for some unknown my radiator cap was loose and the bike wee'd all the coolant so I chucked some water in as I was 50 miles from home and it got me back safely, today I will be getting new coolant, is there a particular one? Also how do I empty the water out of the rad?? Thanks in advance

dirtyred619 26-04-13 08:40 AM

Re: Coolant removal
 
This might help.

http://www.youtube.com/watch?v=vNHqmGKqMdk

Dicky Ticker 26-04-13 08:42 AM

Re: Coolant removal
 
Drain the whole lot out, buy premixed coolant and refill, check for air locks by squeezing the hoses.
By using premix you know you have the correct mixture.
Alternatively if you have a coolant hydrometer to check the specific gravity of your mix use raw coolant

jambo 26-04-13 08:45 AM

Re: Coolant removal
 
1. Undo rad cap
2. Undo water pump drain bolt on the right hand side of the engine.
3. Watch water come out at a surprising rate and angle & spill all over the floor.
4. collect what's left
5. re-seal water pump drain bolt.
6. Lift tank &undo expansion tank filler cap
7. undo small line from just below rad cap to expansion bottle and lower it so water drains into the bucket from there too.
8. reconnect everything, re-fill with chosen coolant (anything for a modern car / aluminium engine will be just fine) first the radiator then the expansion tank.
9. start the engine to work out any air locks then check levels again.
10. beer time!

Jambo

granty92 26-04-13 08:55 AM

Coolant removal - how?
 
Nice one :) will be getting done in a moment

NTECUK 26-04-13 08:55 AM

Re: Coolant removal - how?
 
Don't tip the old stuff down the drain,take it for proper disposal.

m`baubz 26-04-13 01:02 PM

Re: Coolant removal
 
edited slightly for less mess

Quote:

Originally Posted by jambo (Post 2860185)
1. Undo water pump drain bolt on the right hand side of the engine.
2. holding a bucket against the drain undo rad cap
3. Watch water come out at a surprising rate and angle into the bucket
4. look around for suspicious types
5. re-seal water pump drain bolt.
6. Lift tank &undo expansion tank filler cap
7. undo small line from just below rad cap to expansion bottle and lower it so water drains into the bucket from there too.
8. reconnect everything, re-fill with chosen coolant (anything for a modern car / aluminium engine will be just fine) first the radiator then the expansion tank.
9. start the engine to work out any air locks then check levels again.
10. beer time!

Jambo


veenee 26-04-13 03:53 PM

Re: Coolant removal - how?
 
this guide can help as well:

http://bolty.net/2009/08/19/how-to-c...in-your-sv650/

lordra 11-05-13 04:07 PM

Re: Coolant removal - how?
 
Link doesn't work anymore.

veenee 11-05-13 05:18 PM

Re: Coolant removal - how?
 
Yep... Looks like the whole site is down... Shame...

Edit: It looks like it is back up!


All times are GMT. The time now is 03:13 AM.

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.