SV650.org - SV650 & Gladius 650 Forum

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   SV Talk, Tuning & Tweaking (http://forums.sv650.org/forumdisplay.php?f=111)
-   -   Rear cylinder exhaust clamp size? (Curvy) (http://forums.sv650.org/showthread.php?t=199219)

Pricey12 28-05-13 11:00 AM

Rear cylinder exhaust clamp size? (Curvy)
 
I need to buy a nice Mikelor one to go with my shiny Arrow exhaust system, just not sure which size to get (and it's a pig to try and get a look at while still on the bike). I'm thinking it's 43-47mm. Can anyone confirm?

Thanks :)

jambo 28-05-13 11:16 AM

Re: Rear cylinder exhaust clamp size (Curvy)
 
Is the arrow system definitely the same diameter as OE at that point? Might be worth contacting Arrow if not.

Jambo

Pricey12 28-05-13 11:19 AM

Re: Rear cylinder exhaust clamp size (Curvy)
 
Good point, hadn't considered that.

I think the Arrow pipes are actually slightly tapered - will have to check.

Pricey12 28-05-13 01:43 PM

Re: Rear cylinder exhaust clamp size (Curvy)
 
http://i1361.photobucket.com/albums/...psbf639d60.jpg

This is the system - looking at the pipes the diameter of the outlets definitely look bigger than stock. Tape measure time I think :rolleyes:

Pricey12 28-05-13 03:32 PM

Re: Rear cylinder exhaust clamp size (Curvy)
 
One thing I've noticed though, is that the two gasket / clamp attachments (no idea what they're called :rolleyes:) at the end of both headers seem to be rubber, whereas on pictures of other systems I've seen they are metal. Do I need to get hold of some metal ones or can I re-use the ones on the bike? (assuming they haven't turned into paper mache like my front header bolts...

jambo 28-05-13 03:52 PM

Re: Rear cylinder exhaust clamp size (Curvy)
 
If that's what they ship with then that's what you should use, provided they're in decent condition.

I'd use fresh exhaust gaskets, and just assemble it and see if it's blowing anywhere.

Jambo

Pricey12 28-05-13 03:57 PM

Re: Rear cylinder exhaust clamp size (Curvy)
 
Yeah, they seem in good condition.

Doesn't look like you can get the metal versions without buying the entire section of pipe (at least according to Robinson's parts fiche). I just assumed that seeing as the header bolts go through that part to secure the pipe to the bike they would be metal. I guess Arrow must know something I don't...

Pricey12 28-05-13 05:16 PM

Re: Rear cylinder exhaust clamp size (Curvy)
 
Upon inspection, turns out they are metal after all (just painted black). I just assumed they were rubber from the photos :rolleyes:

Pricey12 29-05-13 11:22 AM

Re: Rear cylinder exhaust clamp size? (Curvy)
 
Just out of interest, do you actually NEED a clamp on the rear cylinder header pipe?

It seems to attach in exactly the same way as the front header pipe, and obviously that doesn't have a clamp.

Just curious.

Nobbylad 29-05-13 11:36 AM

Re: Rear cylinder exhaust clamp size? (Curvy)
 
There is an exit pipe from the engine, that the actual exhaust clamps onto....

Not sure if your system replaces that piece and the whole lot bolts on?

http://www.alpha-sports.com/spst/2008/SV650S/35.gif


All times are GMT. The time now is 03:36 PM.

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.