SV650.org - SV650 & Gladius 650 Forum



SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000
Need Help: Try Searching before posting

Reply
 
Thread Tools
Old 17-01-13, 12:51 PM   #1
madnlooney
Guest
 
Posts: n/a
Default K3 not changing between gears 2 and 3

Hi all,
I've got a problem with my k3, it wont change between 2 and 3. Ive checked the clutch position worm thingy, changed the chain as that was knackered and now has the right tension, also new clutch plates. I also checked the bucket for notching but that seemed ok. Its done just over 50k and im not sure what else to now check.
The gear change lever just goes solid and wont move when trying to change up, between 1 and 2 is find. It some times changes up to 3rd then up through the rest fine but it then doesn't go back down to 2nd
Is there anything else i can check or an idea what could be causing it?
  Reply With Quote
Old 17-01-13, 01:22 PM   #2
Elliott
Guest
 
Posts: n/a
Default

So between neutral and 2nd?


Sent from my SV650s using Tapatalk
  Reply With Quote
Old 17-01-13, 01:32 PM   #3
madnlooney
Guest
 
Posts: n/a
Default Re: K3 not changing between gears 2 and 3

no it will go 1st, neutral and 2nd but then from 2nd to 3rd it just dont go. The lever doesnt even move. Just solid
  Reply With Quote
Old 17-01-13, 01:41 PM   #4
Criggers
Guest
 
Posts: n/a
Default

Might be a silly question but have you had the bike long? If it's new to you the person who previously owned it may have switched the gear ratio to 1 up 5 down. Some do this for comfort, just try it the other way, worth a shot
  Reply With Quote
Old 17-01-13, 01:49 PM   #5
madnlooney
Guest
 
Posts: n/a
Default Re: K3 not changing between gears 2 and 3

Quote:
Originally Posted by Criggers View Post
Might be a silly question but have you had the bike long? If it's new to you the person who previously owned it may have switched the gear ratio to 1 up 5 down. Some do this for comfort, just try it the other way, worth a shot
ive had the bike for 3 years and until now its been problem free
  Reply With Quote
Old 17-01-13, 02:08 PM   #6
Criggers
Guest
 
Posts: n/a
Default

Ah right, well I haven't got the foggiest
  Reply With Quote
Old 17-01-13, 03:18 PM   #7
TamSV
Member
Mega Poster
 
TamSV's Avatar
 
Join Date: Feb 2010
Location: Troon, Ayrshire
Posts: 1,812
Default Re: K3 not changing between gears 2 and 3

Try going up the gears with the engine off and see if it's the same. You might need to rock it a wee bit between gears.

Are all the other gear changes OK? Any previous false neutrals while riding or gears grinding?
TamSV is offline   Reply With Quote
Old 17-01-13, 03:23 PM   #8
jambo
Member
Mega Poster
 
jambo's Avatar
 
Join Date: Aug 2003
Location: Croydonia
Posts: 5,376
Default Re: K3 not changing between gears 2 and 3

I'm going out on a limb:
You've not stripped and greased the linkage in a wile and it's sticking. The gear lever moves down into 1st, Up into neutral and up into 2nd, but then it isn't returning cleanly to position, so isn't moving the shift star to the next notch.

To test put some oil / WD40 or similar around the gear lever where it's at the footpeg and wiggle it about a bit. If it gets easier then you've found the issue and can strip and clean it.

If all else fails bring it round to mine and we'll sort it, but you should only need a 10mm spanner and a 6mm hex

Jambo
__________________
Modern motorcycles are bloody brilliant, enjoy it while we can
jambo is offline   Reply With Quote
Old 17-01-13, 03:28 PM   #9
Biker Biggles
Member
Mega Poster
 
Biker Biggles's Avatar
 
Join Date: Jan 2005
Location: Barnet Herts
Posts: 5,071
Default Re: K3 not changing between gears 2 and 3

Quote:
Originally Posted by jambo View Post
I'm going out on a limb:
You've not stripped and greased the linkage in a wile and it's sticking. The gear lever moves down into 1st, Up into neutral and up into 2nd, but then it isn't returning cleanly to position, so isn't moving the shift star to the next notch.

To test put some oil / WD40 or similar around the gear lever where it's at the footpeg and wiggle it about a bit. If it gets easier then you've found the issue and can strip and clean it.

If all else fails bring it round to mine and we'll sort it, but you should only need a 10mm spanner and a 6mm hex

Jambo
Yes.Very simple check and usually cures shifting problems.
__________________
On a clear day we stand there and look further than the ordinary eye can see.
Biker Biggles is offline   Reply With Quote
Old 17-01-13, 04:49 PM   #10
madnlooney
Guest
 
Posts: n/a
Default Re: K3 not changing between gears 2 and 3

Quote:
Originally Posted by TamSV View Post
Try going up the gears with the engine off and see if it's the same. You might need to rock it a wee bit between gears.

Are all the other gear changes OK? Any previous false neutrals while riding or gears grinding?
will try spraying up the gear lever and then try this one after, Thanks for the reply

Quote:
Originally Posted by jambo View Post
I'm going out on a limb:
You've not stripped and greased the linkage in a wile and it's sticking. The gear lever moves down into 1st, Up into neutral and up into 2nd, but then it isn't returning cleanly to position, so isn't moving the shift star to the next notch.

To test put some oil / WD40 or similar around the gear lever where it's at the footpeg and wiggle it about a bit. If it gets easier then you've found the issue and can strip and clean it.

If all else fails bring it round to mine and we'll sort it, but you should only need a 10mm spanner and a 6mm hex

Jambo
Quote:
Originally Posted by Biker Biggles View Post
Yes.Very simple check and usually cures shifting problems.
cheers for the suggestions,
I will give this a go, it makes sense in theory as to why sometimes it shifts up.
If not ill take you up on that offer Jambo
  Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Problems changing gears. bmack999 SV Talk, Tuning & Tweaking 3 24-06-11 09:31 PM
Changing down gears is like standing on a sponge... JimmyGulp Bikes - Talk & Issues 5 19-02-07 11:19 AM
Problems with changing down multiple gears Grinch SV Talk, Tuning & Tweaking 26 16-01-07 12:18 PM
Problem Changing Down Gears leegriffiths128 SV Talk, Tuning & Tweaking 5 03-04-05 11:32 AM


All times are GMT. The time now is 04:17 AM.


Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.