SV Talk, Tuning & Tweaking Discussion and chat on all topics and technical stuff related to the SV650 and SV1000 Need Help: Try Searching before posting |
![]() |
|
Thread Tools |
![]() |
#1 |
Guest
Posts: n/a
|
![]()
Similar to http://forums.sv650.org/showthread.php?t=107342 this thread, on my K3 750 GSXR front ended bike (a '00 SV650s), when I brake a little I can feel something from the disc, and when I'm trailing the brake fairly hard into a right hander there is a massive, huge vibration from mainly the right hand disc. Now I've just changed discs and pads and the problem is still there- it was there before and I put it down to the disc.
Any ideas? Thanks in advance guys |
![]() |
![]() |
#2 |
Member
Mega Poster
Join Date: Dec 2007
Posts: 2,708
|
![]()
Have you checked the wheel run out and balance? Didn't you have a small off recently at Lydden? Is it possible the front tyre has been moved on the rim? If they're all OK I'd probably check the forks next.
|
![]() |
![]() |
![]() |
#3 |
Member
Mega Poster
Join Date: Jan 2008
Location: North West
Posts: 3,124
|
![]()
or both sets of discs could be warped, check them with a dial indicator
|
![]() |
![]() |
![]() |
#4 |
Guest
Posts: n/a
|
![]()
+1 warped disc
|
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]()
If it's warped discs you'll feel the lever pulsing under straight line hard braking ..
|
![]() |
![]() |
#6 |
The Sick Man
Mega Poster
Join Date: Nov 2004
Location: Peckham.SE.LDN
Posts: 4,768
|
![]()
Ive done the same on my SV/GSXR, i warped several sets of disks, could also be wheel bearings. All depends on if you can feal the brake lever pulse or not.
__________________
OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions |
![]() |
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]()
I agree in that it sounds like a warped disc, at low speed you will feel a pulsing through the lever where as at higher speeds it feels like a harsh wobble/vibration.
|
![]() |
![]() |
#8 |
Guest
Posts: n/a
|
![]()
Could be your bearings?
|
![]() |
![]() |
#9 |
Guest
Posts: n/a
|
![]() |
![]() |
![]() |
#10 |
Noisy Git
Mega Poster
Join Date: Apr 2007
Location: Halifax/Leeds
Posts: 26,645
|
![]()
I had a knackered wheel bearing which would only cause wierdness under braking. Not what I would call "massive vibration" though.
__________________
Currently Ex Biker
Now rebuilding a 63' fishing trawler as a dive boat |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Just how much vibration should there be? | leebex | SV Talk, Tuning & Tweaking | 15 | 05-07-09 08:19 PM |
Weird vibration under very heavy braking | chakraist | SV Talk, Tuning & Tweaking | 17 | 14-09-08 05:20 PM |
Bar Vibration | SAMMY650 | SV Talk, Tuning & Tweaking | 5 | 19-06-08 06:08 AM |
Vibration | Giffer2 | SV Talk, Tuning & Tweaking | 24 | 17-06-07 12:09 PM |
Vibration | Grinch | SV Talk, Tuning & Tweaking | 7 | 12-01-07 03:17 PM |