SV650.org - SV650 & Gladius 650 Forum

SV650.org - SV650 & Gladius 650 Forum (http://forums.sv650.org/index.php)
-   Idle Banter (http://forums.sv650.org/forumdisplay.php?f=116)
-   -   How do I find out where the joists are (http://forums.sv650.org/showthread.php?t=121407)

timwilky 19-11-08 01:24 PM

How do I find out where the joists are
 
OK.

so the lounge is fresh decorated. New floor, new laminate, new skirting, new wall paper etc. I now need to hang the new radiator.

Simple position centrally on wall fit valves, drop pipe from valves and drill holes where pipe touches floor. But sods law applies.

My luck and sods law dictates there will be a floor joist at that exact position. So after the event and all the floor was up and I had the opportunity to measure/mark the joist position. How the hell do I detect the positions without going under the floor with a tape measure and a paper&pencil?. Don't tell me there is a standard spacing. This house was built by a guy called jack in the 50s who did not own a spirit level

jimmy__riddle 19-11-08 01:30 PM

Re: How do I find out where the joists are
 
stud detector

timwilky 19-11-08 01:40 PM

Re: How do I find out where the joists are
 
Will they work at that depth?

22mm floor then 3mm foam and 8mm laminate. I would have thought the flooring itself would have bounced back so much that the underlying joist would be lost.

jimmy__riddle 19-11-08 01:47 PM

Re: How do I find out where the joists are
 
might work, if youve got one then its worth a try.

Sudoxe 19-11-08 01:47 PM

Re: How do I find out where the joists are
 
Get a long piece of wood and draw a on the floor using a permanent marker.

Drill a hole, aprox every 1cm along the line to the depth of 1inch.

Get a pencil and poke it through each hole, if it goes straight through the laminate and floor board there isn't a joyce there. If it doesn't go through, there is.

timwilky 19-11-08 01:51 PM

Re: How do I find out where the joists are
 
Quote:

Originally Posted by Sudoxe (Post 1690353)
Get a long piece of wood and draw a on the floor using a permanent marker.

Drill a hole, aprox every 1cm along the line to the depth of 1inch.

Get a pencil and poke it through each hole, if it goes straight through the laminate and floor board there isn't a joyce there. If it doesn't go through, there is.

And get murdered by the wife for all the holes.

sod it, need to don the overalls early and go down into the depths

timwilky 19-11-08 03:34 PM

Re: How do I find out where the joists are
 
So glad I checked before fitting

Placed centrally in the bay, both pipes would have collided with the joists.

so I have to place 2" off centre. I just know some criticising clown will say that it not centred

pmapp 19-11-08 03:37 PM

Re: How do I find out where the joists are
 
Put an offset on yer pipe.

ooo - er missus

Gene genie 19-11-08 04:45 PM

Re: How do I find out where the joists are
 
hit the floor with a hammer. listen to the sound and you'll work out where the joists are.

Quiff Wichard 19-11-08 05:26 PM

Re: How do I find out where the joists are
 
Quote:

Originally Posted by timwilky (Post 1690467)
So glad I checked before fitting

Placed centrally in the bay, both pipes would have collided with the joists.

so I have to place 2" off centre. I just know some criticising clown will say that it not centred


that would be ME !! if I ever visited.. how big is the cavity under the floor then Tim if you got in there??


All times are GMT. The time now is 02:10 AM.

Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.