SV650.org - SV650 & Gladius 650 Forum



Idle Banter For non SV and non bike related chat (and the odd bit of humour - but if any post isn't suitable it'll get deleted real quick).
There's also a "U" rating so please respect this. Newbies can also say "hello" here too.

Reply
 
Thread Tools
Old 19-11-08, 01:24 PM   #1
timwilky
Member
Mega Poster
 
timwilky's Avatar
 
Join Date: Mar 2004
Location: Not in Yorkshire. (Thank God)
Posts: 4,116
Default How do I find out where the joists are

OK.

so the lounge is fresh decorated. New floor, new laminate, new skirting, new wall paper etc. I now need to hang the new radiator.

Simple position centrally on wall fit valves, drop pipe from valves and drill holes where pipe touches floor. But sods law applies.

My luck and sods law dictates there will be a floor joist at that exact position. So after the event and all the floor was up and I had the opportunity to measure/mark the joist position. How the hell do I detect the positions without going under the floor with a tape measure and a paper&pencil?. Don't tell me there is a standard spacing. This house was built by a guy called jack in the 50s who did not own a spirit level
__________________
Not Grumpy, opinionated.
timwilky is offline   Reply With Quote
Old 19-11-08, 01:30 PM   #2
jimmy__riddle
Guest
 
Posts: n/a
Default Re: How do I find out where the joists are

stud detector
  Reply With Quote
Old 19-11-08, 01:40 PM   #3
timwilky
Member
Mega Poster
 
timwilky's Avatar
 
Join Date: Mar 2004
Location: Not in Yorkshire. (Thank God)
Posts: 4,116
Default Re: How do I find out where the joists are

Will they work at that depth?

22mm floor then 3mm foam and 8mm laminate. I would have thought the flooring itself would have bounced back so much that the underlying joist would be lost.
__________________
Not Grumpy, opinionated.
timwilky is offline   Reply With Quote
Old 19-11-08, 01:47 PM   #4
jimmy__riddle
Guest
 
Posts: n/a
Default Re: How do I find out where the joists are

might work, if youve got one then its worth a try.
  Reply With Quote
Old 19-11-08, 01:47 PM   #5
Sudoxe
Guest
 
Posts: n/a
Default Re: How do I find out where the joists are

Get a long piece of wood and draw a on the floor using a permanent marker.

Drill a hole, aprox every 1cm along the line to the depth of 1inch.

Get a pencil and poke it through each hole, if it goes straight through the laminate and floor board there isn't a joyce there. If it doesn't go through, there is.
  Reply With Quote
Old 19-11-08, 01:51 PM   #6
timwilky
Member
Mega Poster
 
timwilky's Avatar
 
Join Date: Mar 2004
Location: Not in Yorkshire. (Thank God)
Posts: 4,116
Default Re: How do I find out where the joists are

Quote:
Originally Posted by Sudoxe View Post
Get a long piece of wood and draw a on the floor using a permanent marker.

Drill a hole, aprox every 1cm along the line to the depth of 1inch.

Get a pencil and poke it through each hole, if it goes straight through the laminate and floor board there isn't a joyce there. If it doesn't go through, there is.
And get murdered by the wife for all the holes.

sod it, need to don the overalls early and go down into the depths
__________________
Not Grumpy, opinionated.
timwilky is offline   Reply With Quote
Old 19-11-08, 03:34 PM   #7
timwilky
Member
Mega Poster
 
timwilky's Avatar
 
Join Date: Mar 2004
Location: Not in Yorkshire. (Thank God)
Posts: 4,116
Default Re: How do I find out where the joists are

So glad I checked before fitting

Placed centrally in the bay, both pipes would have collided with the joists.

so I have to place 2" off centre. I just know some criticising clown will say that it not centred
__________________
Not Grumpy, opinionated.
timwilky is offline   Reply With Quote
Old 19-11-08, 03:37 PM   #8
pmapp
Member
Mega Poster
 
pmapp's Avatar
 
Join Date: Jun 2006
Location: Wakefield, West Yorks'
Posts: 1,129
Default Re: How do I find out where the joists are

Put an offset on yer pipe.

ooo - er missus
__________________
'52 Curvy S | So good.....it made me want to trump!

If at first you don't succeed - use more gaffa tape.
pmapp is offline   Reply With Quote
Old 19-11-08, 04:45 PM   #9
Gene genie
Guest
 
Posts: n/a
Default Re: How do I find out where the joists are

hit the floor with a hammer. listen to the sound and you'll work out where the joists are.
  Reply With Quote
Old 19-11-08, 05:26 PM   #10
Quiff Wichard
Guest
 
Posts: n/a
Default Re: How do I find out where the joists are

Quote:
Originally Posted by timwilky View Post
So glad I checked before fitting

Placed centrally in the bay, both pipes would have collided with the joists.

so I have to place 2" off centre. I just know some criticising clown will say that it not centred

that would be ME !! if I ever visited.. how big is the cavity under the floor then Tim if you got in there??
  Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Where can I find clutch housing bolts? - Cant find any mikeSV SV Talk, Tuning & Tweaking 2 24-03-08 12:30 PM
Trying to find an SV davidimurray Bikes - Talk & Issues 11 10-08-07 09:29 AM
I can't find........ svrash Bikes - Talk & Issues 0 19-02-06 03:26 PM
Would like to find... REEVESIE Bikes - Talk & Issues 2 17-04-05 11:01 AM


All times are GMT. The time now is 02:34 PM.


Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.