Chop, chop, buzz, buzz. - SV650.org

17-09-07, 09:05 AM

Been getting busy with me dremel.

Next is to make a template from it once I have cleaned the edges a bit to get the other side the same.

17-09-07, 09:07 AM

Interesting, don't you think it's going to flap in the wind without the rad mount?

17-09-07, 09:56 AM

Well it would only be that bit that would flap, the rest is secured to the front fairing mount, so should be just fine. So I now have a 'quarter' fairing.

17-09-07, 04:06 PM

Be inneresting to see the completed job...

18-09-07, 09:22 PM

any photo's of it fitted to the bike?

20-09-07, 11:29 AM

Quote:

Originally Posted by kwak zzr

any photo's of it fitted to the bike?

Not at the moment, though this weekend I shall hopefully doing some work on it. So will take some pics then.

28-09-07, 02:32 PM

Quote:

Originally Posted by Grinch

Not at the moment, though this weekend I shall hopefully doing some work on it. So will take some pics then.

Hows it goin ? got any pics yet ?

28-09-07, 03:52 PM

Well due to the naff weather its been delayed a tad, though I was out with the compressor and the sander today after working on a Aprilia Caponard to sand the panels down and its looking nice, taking my time though I am. Next I need to plastic weld a few bits and make sure it lines up with the main fairing, maybe sand that to. Hoping to get a few clear days for that next week.

08-10-07, 08:38 AM

Well here you are a few pics from the weekend testing.

Still a bit unsure as I might need to trim the front below the lights and air scoop a bit more to make the lines flow better.

08-10-07, 08:51 AM

was the original faring damaged or did you just fancy something different?

17-09-07, 09:05 AM	#1
Grinch Guest Posts: n/a	Chop, chop, buzz, buzz. Been getting busy with me dremel. Next is to make a template from it once I have cleaned the edges a bit to get the other side the same.

17-09-07, 09:07 AM	#2
Razor Guest Posts: n/a	Re: Chop, chop, buzz, buzz. Interesting, don't you think it's going to flap in the wind without the rad mount?

17-09-07, 09:56 AM	#3
Grinch Guest Posts: n/a	Re: Chop, chop, buzz, buzz. Well it would only be that bit that would flap, the rest is secured to the front fairing mount, so should be just fine. So I now have a 'quarter' fairing.

17-09-07, 04:06 PM	#4
Razor Guest Posts: n/a	Re: Chop, chop, buzz, buzz. Be inneresting to see the completed job...

18-09-07, 09:22 PM	#5
kwak zzr Guest Posts: n/a	Re: Chop, chop, buzz, buzz. any photo's of it fitted to the bike?

28-09-07, 03:52 PM	#8
Grinch Guest Posts: n/a	Re: Chop, chop, buzz, buzz. Well due to the naff weather its been delayed a tad, though I was out with the compressor and the sander today after working on a Aprilia Caponard to sand the panels down and its looking nice, taking my time though I am. Next I need to plastic weld a few bits and make sure it lines up with the main fairing, maybe sand that to. Hoping to get a few clear days for that next week.

08-10-07, 08:38 AM	#9
Grinch Guest Posts: n/a	Re: Chop, chop, buzz, buzz. Well here you are a few pics from the weekend testing. Still a bit unsure as I might need to trim the front below the lights and air scoop a bit more to make the lines flow better.

08-10-07, 08:51 AM	#10
kwak zzr Guest Posts: n/a	Re: Chop, chop, buzz, buzz. was the original faring damaged or did you just fancy something different?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Curvy engine won't start, electrical buzz.	Geoffrey	Bikes - Talk & Issues	13	25-08-08 04:45 PM
For sale: Playstation 2 with lots of bits and pieces inc Buzz & Singstar & Lots more	Paul the 6th	Idle Banter	3	25-04-08 12:52 PM
Upgrade 650 - 1000: Same buzz?	exduker	SV Talk, Tuning & Tweaking	5	16-03-05 09:42 PM