SV650.org - SV650 & Gladius 650 Forum



Photos Place your images here. There's also a "U" rating so please respect this.

Reply
 
Thread Tools
Old 22-01-08, 10:56 PM   #101
aarond
Guest
 
Posts: n/a
Default Re: Stubbie'd my endcan.

Quote:
Originally Posted by Wideboy View Post
will probably do it at weekend, unsure how it will look not being a high level
mine isn't a high level either so will put a pic up when done which should hopefully be tomorrow as i need to get some 4mm rivets tomorrow.
  Reply With Quote
Old 22-01-08, 11:00 PM   #102
Wideboy
Evel Knievel
Mega Poster
 
Wideboy's Avatar
 
Join Date: Jun 2007
Location: Eastleigh
Posts: 4,641
Default Re: Stubbie'd my endcan.

Quote:
Originally Posted by ad53ggz View Post
mine isn't a high level either so will put a pic up when done which should hopefully be tomorrow as i need to get some 4mm rivets tomorrow.

ok cheers mate look forward to it
__________________

05 DRZ400E
RIP hovis
Wideboy is offline   Reply With Quote
Old 23-01-08, 12:12 AM   #103
Richie
fantabulas
Mega Poster
 
Richie's Avatar
 
Join Date: Apr 2004
Location: Nr Durham
Posts: 4,940
Default Re: Stubbie'd my endcan.

Quote:
Originally Posted by amarko5 View Post
yeah but mine is the one where you have that big plate of spagetti and the string going from mouth to mouth
amazing what photoshop can do
you sir are a very very bad man.

__________________
My Flickr photos
Richie is offline   Reply With Quote
Old 23-01-08, 06:07 PM   #104
aarond
Guest
 
Posts: n/a
Default Re: Stubbie'd my endcan.

Quote:
Originally Posted by Wideboy View Post
ok cheers mate look forward to it
job done looks good an sounds good(in my opinion!!)



  Reply With Quote
Old 23-01-08, 06:13 PM   #105
Wideboy
Evel Knievel
Mega Poster
 
Wideboy's Avatar
 
Join Date: Jun 2007
Location: Eastleigh
Posts: 4,641
Default Re: Stubbie'd my endcan.

that looks ace! thought it would look rubbish with out being a high level

how long did you make it?, shame about where the strap is

might do mine at the week end
__________________

05 DRZ400E
RIP hovis
Wideboy is offline   Reply With Quote
Old 23-01-08, 06:21 PM   #106
aarond
Guest
 
Posts: n/a
Default Re: Stubbie'd my endcan.

i took about 7.5inches off i did it like yorkie chris by taking off the bottom cap and cutting out a section on the bottom but if i was doing it again i think i would take off the top cap and cut the top because the center cylinder bit of the exhaust was a b**ch to get back into the top end cap maybe worth taking a note how far the center cylinder tube goes into the end cap.hope this makes sense
  Reply With Quote
Old 23-01-08, 06:22 PM   #107
aarond
Guest
 
Posts: n/a
Default Re: Stubbie'd my endcan.

N.B. forgot to say DO IT
  Reply With Quote
Old 23-01-08, 06:24 PM   #108
Wideboy
Evel Knievel
Mega Poster
 
Wideboy's Avatar
 
Join Date: Jun 2007
Location: Eastleigh
Posts: 4,641
Default Re: Stubbie'd my endcan.

why was the tube hard to get back into the top cap? and how did you eventually do it?
__________________

05 DRZ400E
RIP hovis
Wideboy is offline   Reply With Quote
Old 23-01-08, 06:39 PM   #109
aarond
Guest
 
Posts: n/a
Default Re: Stubbie'd my endcan.

well it was just hard to get it lined up right, patience was the main thing then start hitting/taping then end cap in. Like those before i had to cut notches in the end cap and bend them over a bit to aid getting the end cap into the exhaust. N.b. also hard cos it is a tight fit in the first place!
  Reply With Quote
Old 23-01-08, 06:41 PM   #110
Richie
fantabulas
Mega Poster
 
Richie's Avatar
 
Join Date: Apr 2004
Location: Nr Durham
Posts: 4,940
Default Re: Stubbie'd my endcan.

Looks cool mate, bet it sounds the mutts danglies too.
__________________
My Flickr photos
Richie is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
"Polishing" my endcan netsurfer Bikes - Talk & Issues 1 07-01-07 11:34 PM


All times are GMT. The time now is 08:28 PM.


Powered by vBulletin® - Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.