New number plate hanger & My bike being fixed - Page 2 - SV650.org

02-01-06, 01:17 AM

ta for the answer-
I wear a rucksack and worry somtimes if I shud or not..

My neighbour is a pain - cos he is a bad driver he leaves loads of spac behind him and therefore just blocks my exit a little....

I caught his bumper once and gouged out a 6 inch scrape- he made me pay him £20 !!

TSM · 02-01-06, 11:43 PM

My skidmarx bellypan took a bad grase to the left side on the road, it made a large hole, also the mounting point was broken. So a bit of fiberglass fixed all that, a nice bit of sanding until a smooth finish (only bothered about the outside), a bit of spraying and voila. The best work i have produced myself.

While i was at it, i have my leo vince can looking a bit bent so decided to pull it apart. You can see at the cap end that its bent, well it was pointing downwards. I think im going to hack that bit off and make the can shorter. Not a major thing as i have another one on the bike.

02-01-06, 11:43 PM	#12
TSM The Sick Man Mega Poster Join Date: Nov 2004 Location: Peckham.SE.LDN Posts: 4,768	My skidmarx bellypan took a bad grase to the left side on the road, it made a large hole, also the mounting point was broken. So a bit of fiberglass fixed all that, a nice bit of sanding until a smooth finish (only bothered about the outside), a bit of spraying and voila. The best work i have produced myself. While i was at it, i have my leo vince can looking a bit bent so decided to pull it apart. You can see at the cap end that its bent, well it was pointing downwards. I think im going to hack that bit off and make the can shorter. Not a major thing as i have another one on the bike. __________________ OTR: KTM 690 Duke R 2015 Full Akro SIDELINE: Kwak ZX636 A1P 2002, Red, R&G's, Yoshi, Double Bubble Screen GONE: Kwak ZX-7R P1, Full Akro, Undertray, Screen GONE: SV650S K2 Very Bruised & Without Fairing, Motovation Frame Sliders, R&G Ally Sprocket Toe Protector, HEL 2 Line Setup, GSXR K1 600 RWU Forks, Barnett Clutch & Springs, Penske 8981 Shock, Gilles Ti Rearsets, Steel Barends, Scottoiler, AFAM Chain & Sprockets, Twin FIAMM Horns, Skidmarx Bellypan, Full Micron Zeta Steel System, Cut down undertay. Forum Problems & Information / Site Suggestions

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Anyone made an exhaust hanger/number plate holder? and other metalwork questions	monkey	Bikes - Talk & Issues	2	13-05-09 07:02 AM
Got a £30 fixed penalty for small reg plate today. Bummer!	streetos	Bikes - Talk & Issues	21	05-05-06 12:34 PM
Removing number plate hanger.	DanAbnormal	SV Talk, Tuning & Tweaking	12	20-03-06 08:48 PM
Number plate hanger	The Mass	SV Talk, Tuning & Tweaking	0	10-08-05 08:27 PM
number plate hanger	matsv650s	SV Talk, Tuning & Tweaking	2	16-06-05 05:18 PM

02-01-06, 01:17 AM	#11
Quiff Wichard Guest Posts: n/a	ta for the answer- I wear a rucksack and worry somtimes if I shud or not.. My neighbour is a pain - cos he is a bad driver he leaves loads of spac behind him and therefore just blocks my exit a little.... I caught his bumper once and gouged out a 6 inch scrape- he made me pay him £20 !!