Cutting my exhaust - SV650.org

13-02-06, 04:03 PM

Im fairly new to this site and have found a lot of info that im sure will come in handy sooner or later.

Now i want to cut my stock exhaust and fit something different, problems are.
1 where exactly should i cut.
2 what exhaust can should i fit, i would prefer one that looks smart that i dont have to tinker with the fueling.
3 one that sits a little higher than the stock one.

SV650s K4 2004 model and want to keep the rear pegs for the misses.

Looked at lots of pictures but still none the wiser.

Buget is about £150.

Grant.

13-02-06, 04:39 PM

Quote:

Originally Posted by sennamontoya

1 where exactly should i cut. Its normally 40mm above the weld (near the R/H footpeg

) The can you buy will come with instructions though (specific to that can

)
2 what exhaust can should i fit, i would prefer one that looks smart that i dont have to tinker with the fueling. I'd go for a Carbon Can Company (CCC) can with your budget TBH

3 one that sits a little higher than the stock one. You can get a 'high-level' link pipe, but if you want to keep the rear pegs, you'll need extenders fitting to the R/H side pillion peg - CCC may have these too!

Hope this helps

CCC direct (on eBay) here - £110

13-02-06, 06:34 PM

Hello,

CCC do not fit very well high level on the k4>k6 models, well not as standard anyway, this can be rectified!!!

AND

But this can be cured,

CCC are aware of this but don't seem to be too bothered about solving it, hence the DIY aproach, can supply more info if you wish but you will be able to get one for about the £150 mark new.

Lawrence

14-02-06, 10:23 AM

I asked the question about going 'high-level' on the eBay ad... The reply was...

Quote:

Originally Posted by CCC

If you would like a can with a high level pipe call me at work for prices and spec, 01253 877900, Simon.

14-02-06, 04:52 PM

I hope it fits well as i have just bought a high level Carbon can co. can.

Havent had time to fit it yet ( but if it looks like that its going straight back to Fleetwood ).

Looks very good in the box though - lol

14-02-06, 05:30 PM

Good luck MAC!!!

Let me know if it fits, i've phoned, emailed and even spoke to the guys at CCC face to face about this!!! And there answer was, we designed it to fit the k3, we've never had a later model in for a refit, if you want to bring your bike to us for a fitting that'll be ok, as far as we're aware its not a problem!!!! ETC ETC ETC!!!!

Main problem is the fitting bar, not the link pipe!!! MAC what bar have they supplied you??? a straight one??

Lawrence

13-02-06, 04:03 PM	#1
buell Guest Posts: n/a	Cutting my exhaust Im fairly new to this site and have found a lot of info that im sure will come in handy sooner or later. Now i want to cut my stock exhaust and fit something different, problems are. 1 where exactly should i cut. 2 what exhaust can should i fit, i would prefer one that looks smart that i dont have to tinker with the fueling. 3 one that sits a little higher than the stock one. SV650s K4 2004 model and want to keep the rear pegs for the misses. Looked at lots of pictures but still none the wiser. Buget is about £150. Grant.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cutting the Exhaust!	hoppy34	SV Talk, Tuning & Tweaking	6	22-07-07 10:33 PM
cutting off exhaust	jay boi	Exhausts	5	03-05-07 07:09 PM
Cutting off exhaust..	StreetHawk	Exhausts	12	29-04-07 09:50 PM
Cutting exhaust	gemm1984	SV Talk, Tuning & Tweaking	14	30-07-06 06:31 PM
Cutting exhaust	wtdafk	Bikes - Talk & Issues	1	29-04-06 03:30 PM

13-02-06, 06:34 PM	#3
lodman27 Guest Posts: n/a	Hello, CCC do not fit very well high level on the k4>k6 models, well not as standard anyway, this can be rectified!!! AND But this can be cured, CCC are aware of this but don't seem to be too bothered about solving it, hence the DIY aproach, can supply more info if you wish but you will be able to get one for about the £150 mark new. Lawrence

14-02-06, 04:52 PM	#5
mac Guest Posts: n/a	I hope it fits well as i have just bought a high level Carbon can co. can. Havent had time to fit it yet ( but if it looks like that its going straight back to Fleetwood ). Looks very good in the box though - lol

14-02-06, 05:30 PM	#6
lodman27 Guest Posts: n/a	Good luck MAC!!! Let me know if it fits, i've phoned, emailed and even spoke to the guys at CCC face to face about this!!! And there answer was, we designed it to fit the k3, we've never had a later model in for a refit, if you want to bring your bike to us for a fitting that'll be ok, as far as we're aware its not a problem!!!! ETC ETC ETC!!!! Main problem is the fitting bar, not the link pipe!!! MAC what bar have they supplied you??? a straight one?? Lawrence