remake of the supports for the givi suitcases - SV650.org

13-06-12, 12:35 PM

Hi everyone!

Well I´m new here, so I´ve to introduce myself, I´m from Madrid, Spain, and I've a sv650s k5 since 4 years. I let a photo of my "susy" and me.

Well, so this July I´m going to travel from Madrid to North Cape with four friends. So we need to carry luggage, and for this I decided to buy the givi
tph01.

I didn't want to carry a big suitcases, so finally I decided to buy these in spite of there weren't available for our suzuki. No problem

,I compared the different models available with this suitcase and also the anchors (sorry for my english) and I thought that the most similar was the anchors of the Yamaha XJ6/ XJ6 División 09>10

so let start! We remove the passenger seat

we decided to fix the anchors to these four point that shown in the picture

we put the anchors near to the tail and decide the position, the anchors were joined to the tail through welding a special pieces.

the lowest anchor, we decided to put there (shows in the picture)

so we cuted and fold the anchors to the desired position

the measurements of the rear plates is 12 cm ... measure, mark cut

continue...

13-06-12, 12:45 PM

Well, the same procedure for the bottom plate in the photo (blurry, sorry are made with the phone) and shows the bottom plate welded. The other plate is marked well above decided to cut and weld plate

The mark is where is where we cut, the other circle is support cut and where it comes home to hang the helmet under the seat. It is also necessary to reduce the plastic then the seat can be closed without problems.

Same process for manufacturing the plate, in this case so that everything is perfect, we weld the brackets placed on the bike subjects in the two bars that we've done. Attention! remove the negative battery terminal when the welding is to be on the bike

the piece that connects the two brackets from behind is short, so we cut in half and weld a charge of 10 cm. then polish the welds and paint ...

and assemble...

Hope you like it!

embee · 13-06-12, 12:51 PM

Welcome to the forum. Nice work and very well presented!

Jayneflakes · 13-06-12, 01:00 PM

Hola y bienvenido al foro.

Very impressive, I like your work.

Welcome to the forum, it looks like you will have a lot of ideas to bring in with you.

13-06-12, 03:25 PM

Thank you for the welcome! I hope I could apport more ideas or knowledge

maviczap · 13-06-12, 03:53 PM

I hate people with big garages & workshop facilities

garage envy

Hello

You've got some carbon thing going on with your SV's rear end

Bibio · 13-06-12, 04:53 PM

nice work. welcome to the org.

yes it's crap having those sort of facility's at your disposal

squirrel_hunter · 13-06-12, 05:11 PM

Quote:

Originally Posted by embee

Welcome to the forum. Nice work and very well presented!

Agreed.

SIII · 13-06-12, 06:03 PM

tres bocadillos de queso - the only spanish i know!

Nice work, i am inspired. well done & welcome.

13-06-12, 06:58 PM

Nice work.
The Carbon rear end, is it real Carbon og wrap?

13-06-12, 12:35 PM	#1
Willy-sv Guest Posts: n/a	remake of the supports for the givi suitcases Hi everyone! Well I´m new here, so I´ve to introduce myself, I´m from Madrid, Spain, and I've a sv650s k5 since 4 years. I let a photo of my "susy" and me. Well, so this July I´m going to travel from Madrid to North Cape with four friends. So we need to carry luggage, and for this I decided to buy the givi tph01. I didn't want to carry a big suitcases, so finally I decided to buy these in spite of there weren't available for our suzuki. No problem,I compared the different models available with this suitcase and also the anchors (sorry for my english) and I thought that the most similar was the anchors of the Yamaha XJ6/ XJ6 División 09>10 so let start! We remove the passenger seat we decided to fix the anchors to these four point that shown in the picture we put the anchors near to the tail and decide the position, the anchors were joined to the tail through welding a special pieces. the lowest anchor, we decided to put there (shows in the picture) so we cuted and fold the anchors to the desired position the measurements of the rear plates is 12 cm ... measure, mark cut continue... Last edited by Willy-sv; 13-06-12 at 03:17 PM.

13-06-12, 12:45 PM	#2
Willy-sv Guest Posts: n/a	Re: remake of the supports for the givi suitcases Well, the same procedure for the bottom plate in the photo (blurry, sorry are made with the phone) and shows the bottom plate welded. The other plate is marked well above decided to cut and weld plate The mark is where is where we cut, the other circle is support cut and where it comes home to hang the helmet under the seat. It is also necessary to reduce the plastic then the seat can be closed without problems. Same process for manufacturing the plate, in this case so that everything is perfect, we weld the brackets placed on the bike subjects in the two bars that we've done. Attention! remove the negative battery terminal when the welding is to be on the bike the piece that connects the two brackets from behind is short, so we cut in half and weld a charge of 10 cm. then polish the welds and paint ... and assemble... Hope you like it!

13-06-12, 12:51 PM	#3
embee Member Mega Poster Join Date: Jul 2003 Location: Warwickshire Posts: 2,801	Re: remake of the supports for the givi suitcases Welcome to the forum. Nice work and very well presented! __________________ "Artificial Intelligence is no match for natural stupidity"

13-06-12, 03:25 PM	#5
Willy-sv Guest Posts: n/a	Re: remake of the supports for the givi suitcases Thank you for the welcome! I hope I could apport more ideas or knowledge

13-06-12, 03:53 PM	#6
maviczap Member Mega Poster Join Date: Mar 2007 Posts: 9,096	Re: remake of the supports for the givi suitcases I hate people with big garages & workshop facilities garage envy Hello You've got some carbon thing going on with your SV's rear end __________________ We're riding out tonight to case the promised land Make everyday count RIP Reeder - Jolly Green Giant and comedy genius

13-06-12, 04:53 PM	#7
Bibio Member Mega Poster Join Date: Jul 2008 Location: here as devil's advocate Posts: 11,540	Re: remake of the supports for the givi suitcases nice work. welcome to the org. yes it's crap having those sort of facility's at your disposal

13-06-12, 06:03 PM	#9
SIII Member Mega Poster Join Date: Apr 2010 Location: Dumfries and Galloway Posts: 1,319	Re: remake of the supports for the givi suitcases tres bocadillos de queso - the only spanish i know! Nice work, i am inspired. well done & welcome. __________________ "You know, Scotland has its own martial arts. Yeah, it's called Fuk-U. It's mostly just head butting and then kicking people when they're on the ground" The Stoppy King

13-06-12, 06:58 PM	#10
MMN Guest Posts: n/a	Nice work. The Carbon rear end, is it real Carbon og wrap?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Givi V46 topbox, Givi M5 plate, Givi 529FZ monorack	sc00by	Stuff Wanted	0	12-03-12 02:40 PM
James bond supports international women's day 2011	toxic	Idle Banter	1	08-03-11 10:47 PM
Who supports the Unions uprising?	ThEGr33k	Idle Banter	113	15-09-10 08:46 PM
Suitcases	Shellywoozle	Idle Banter	22	24-04-08 10:21 PM
Remake of gone in 60 seconds	sharriso74	Idle Banter	8	03-07-06 04:25 PM